Maintenance; Operation - RAMSEY WINCH HD-P8000 Manual De Funcionamiento, Reparación Y Mantenimiento

CABLE DRUM
ROTATION DIRECTION
CARTRIDGE
POSITION
"A" ROTATION

MAINTENANCE

1. Inspect the cable for damage and lubricate frequently. If the cable becomes frayed with broken strands, replace immediately. Cable and
hook assembly (100' long cable) P/N 524118 ("Y" drum) or (150' long cable) P/N 524119 (STD drum) may be purchased from a
Ramsey distributor.
2. Check that the clutch is fully engaging. See OPERATION instructions, above, for the appropriate clutch shifter. FOR MANUAL CLUTCH
ONLY: Monthly, disengage clutch, put several drops of oil on the clutch handle shaft and work clutch handle IN and OUT several times
to lubricate inside the shifter assembly.
3. Check to see that the drum cable does not overrun ("birdnest") when freespooling. Refer to page 4 if it does.
4. Replace drum bushings and seals if seals begin to seep grease. Refer to the Overhaul Instructions, pages 8-10. Add additional lubri-
cant, Mobilith SHC 007, to gears and drum bearings if required.

OPERATION

The best way to get acquainted with how your winch operates is to make test runs before you actually use it. Plan your test in advance.
Remember, you hear your winch as well as see it operate. Get to recognize the sounds of a light steady pull, a heavy pull, and sounds
caused by load jerking or shifting. Avoid conditions where load shifts or jerks occur, as they may indicate a dangerous situation.
The uneven spooling of cable, while pulling the load, is not a problem, unless there is a cable pileup on one end of the drum. If this happens,
reverse the winch to relieve the load, and move your anchor point further to the center of the vehicle. After the job is done you can unspool
and rewind for a neat lay of the cable.
When pulling a heavy load, place a blanket, jacket, and tarpaulin over the cable about five or six feet behind the hook. In the event of a bro-
ken cable, this will slow the snap back of the cable and could prevent serious injury.
The winch clutch allows rapid unspooling of the cable, from the cable drum, for hooking onto the load. The clutch is operated by the clutch
shifter lever or air shifter.
MANUAL CLUTCH SHIFTER (Refer to dimensional drawing page 11):
TO DISENGAGE CLUTCH: Run the winch in the reverse (reel out) direction until the load is off the cable. Pull handle out and rotate 90°. With
handle in the "DISENGAGED" position, cable may now be free-spooled from the drum.
TO ENGAGE CLUTCH: Pull handle out, rotate 90° and release handle. Run the winch in reverse until the clutch handle snaps fully into the
"ENGAGED" position. DO NOT attempt to pull a load unless the handle is fully at the "ENGAGED" position. If manual shift indicator light is
present, the green light is lit when clutch is fully "ENGAGED". DO NOT attempt to pull a load unless the green light is lit. To install light to the
vehicle electrical system refer to the Electrical Schematic on page 12.
AIR CYLINDER CLUTCH SHIFTER (Refer to the dimensional drawing page 12):
TO DISENGAGE CLUTCH: Run the winch in the reverse (reel out) direction until load is off the cable. Apply air pressure to the .125-27 NPT
port: 80 PSI (min.)-150 PSI (max.). CAUTION: PRESSURE MUST NOT EXCEED 150 PSI.
TO ENGAGE CLUTCH: Remove air pressure from the cylinder (a return spring engages the plunger). Run winch in reverse until the clutch
engagement indicator light (green light) is lit. To install light to the vehicle electrical system refer to the Electrical Schematic on page 12.
ROTATION DIRECTION
PLUG
POSITION
(REEL IN) RAISE INLET
WARNING: DO NOT DISENGAGE CLUTCH UNDER LOAD!
5
CABLE DRUM
CARTRIDGE
POSITION
"B" ROTATION