Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
4) IR remote MODE:
The laser can be controlled by the IR remote control:
Press the FUNC-button until the display shows: "REM".
Press the ENTER-button to confirm your choice.
Note:
In any standalone mode (excepted REM and SLA), press ON/OFF for 2 second to activate remote
function.
AUTO SHOW
MUSIC SHOW
LASER ON/OFF
COLOR
EFFECT PAUSE
CHANGING PATTERN
SOUND SENSIVITY
FIXED PATTERN (FROM 1 TO 48)
PATTERN REPEATING
Remote control details:
Button
function
In REM mode, turn on/off the laser. In any oder
ON/OFF
standalone mode except SLAVE, press 2s to turn on the
AUTO
Sound activated show, the blue is flashing when the
MUSIC
In sound activated mode, press music+B+1to 9 to change
Sound sensivity
COLOR
To change the color from red to green or red & green
CHANGING
PATTERN
CHANGING
FIXED
PATTERN
PATTERN
Last pattern and current pattern cycle repeating
REPEAT
5) DMX512 MODE:
The laser can be controlled by any standard DMX-controller in 2 different DMX-modes:
1 CHANNEL MODE: for extremely easy setup and use! (display shows "1Ch")
17 CHANNEL MODE: for full control on every functionalities. (display shows "17c")
Connect the DMX input of the laser to the DMX output of the previous unit in the chain or directly to the
DMX-output of your controller.
Press the FUNC-button until the display shows: "1Ch" or "17h".
JB SYSTEMS
®
USER MANUAL
Description
REM mode
Auto running show
sound is detected.
the sensivity settings
To show and change patterns
You can select one pattern from 1 to 48
7/74
SMOOTH SCAN-BLUE LASER
ENGLISH
Press the UP/DOWN buttons to select the DMX-mode. (1ch or 17ch)
Press the ENTER-button to confirm your choice.
Press the FUNC-button: the 3 digit number on the display starts blinking.
Select the DMX-address
Press the ENTER-button to confirm your choice.
Note: the display blinks when the unit is in DMX-mode and no DMX-signal is detected.
Some more information on DMX512:
The DMX-protocol is a widely used high speed signal to control intelligent light
equipment. You need to "daisy chain" your DMX controller and all the connected light
effects with a good quality XLR M/F balanced cable. To prevent strange behavior of the
light effects, due to interferences, you must use a 90Ω to 120Ω terminator at the end of
the chain. Never use Y-splitter cables, this simply won't work!
Each effect in the chain needs to have its proper starting address so it knows which commands from the
controller it has to decode.
1 CHANNEL DMX-CONFIGURATION OF THE LASER:
DMX-
position
value
function
4
210-255
SOU
3
150-209
AUT
2
090-149
SOP
1
030-089
AUP
0
000-029
STANDBY
17 CHANNEL DMX-CONFIGURATION OF THE LASER:
IMPORTANT REMARK: DMX Channel1 is used to set the different working modes of the laser.
To use the laser in full 17 channel mode, channel 1 must be set to value 221 or higher.
Depending on the DMX-values of channel1, different mode can be applied:
DMX-
Channel
value
000-040
041-080
081-120
CH1
Mode
121-160
161-200
201-255
000-051
052-103
CH2
104-155
Group
156-207
208-255
CH3 Pattern
000-255
JB SYSTEMS
®
USER MANUAL
remarks
Sound activated show
Automatic show
Sound activated pattern effect show
Auto running pattern effect show
Laser output off
function
Laser OFF
AUT
SOU
AUP
SOP
DMX MODE
1 Group Patterns.
2 Group Patterns
3 Group Patterns
4 Group Patterns
5 Group Patterns
Every 16 for 1 group, total 80 patterns.
8/74
SMOOTH SCAN-BLUE LASER
Publicidad
