Demolition And Disposal - Tecomec Midi Jolly-N Manual De Instrucciones

- easy grinder :
• if the knob is turned clockwise, the chain is locked between the
two jaws, for precise and safe grinding (photo 11)
- grind all teeth of the same type (right) before turning the vise on
the opposite side, to start grinding left teeth (photo 12), without
touching the chain feed register screw (photo 8 - point 1)
At the end of grinding operations, turn off the grinder, disconnect
the cable from the mains, and remove the grinder, placing it in a
safe place, away from children.
N.B. If the chain depth gauge is too high with respect to the tooth
(usually after 2/3 grinding operations), lower it using a flat file
(photo 13). For the height of the depth gauge, consult the chain
table enclosed at the end of the handbook (column M).
N.B.
- do not use cooling fluids while grinding
- if, when you turn the switch to "1", the grinder does not start,
and if when the switch is in the "0" position the grinder does
not stop, promptly disconnect the power cable from the mains
- if the wheel is banged or hit by accident during grinding,
follow the instructions provided in paragraph ASSEMBLY AND
WARNINGS ABOUT THE GRINDING WHEEL
TROUBLESHOOTING
- The machine does not start:
- check that the plug is perfectly connected to the outlet
- check that the power cable of the machine is not damaged
- check that the outlet is energized
- check that no fuses have blown in the outlet
- check that the automatic circuit-breaker has not tripped.
If, after these operations, the failure to start can be attributed to the
machine, have it checked by an authorized service center.
- The connection of the machine to the mains makes the
automatic circuit-breaker trip:
- contact an authorized service center.
- The machine's electrical motor is overheated:
- check that the voltage indicated on the data plate meets the mains
voltage
- comply the max. time (15 min.) recommended for continuous
operation
- check that la wheel does not block during grinding
If the problem persists, contact and authorized service center.
- The direction of rotation of the wheel is the opposite of that
indicated on the machine:
- contact an authorized service center
- The machine shows signs of anomalous vibrations:
- check that the machine is secured to the work bench
- check that the motor unit is secured to the base unit
- check that the wheel is properly installed on the relevant centering
hub
If the problem persists, contact and authorized service center.
MAINTENANCE
- always disconnect the plug from the socket before carrying out any
maintenance, lubrication or cleaning operations
- the grinder must be kept clean, in order to make safety instructions
and plates clearly legible. Clean it using a rag or a swab.
- do not use compressed air, that is likely to bring the metal dust
in positions where they cannot be reached, damaging essential
components of the grinder.

DEMOLITION AND DISPOSAL

The machine is to be demolished by qualified personnel in
compliance with current laws in force in the country in which it is
installed.
The symbol (on the rating nameplate) points out that the
product must not be disposed of with normal household garbage.
Contact an authorized tip or your dealer for disposal instructions.
Before you scrap the machine, make it unusable by cutting
the power supply cable for example and make the parts
safe, which could cause a source of danger for children if
they should play with the machine.
6
EN
WARRANTY
- the validity of the warranty on this product is subject to the
recognition of the country of sale. To be valid, any claim
must be accompanied by a copy of the purchase documents
(invoice or cash voucher) and product packaging (if possible
intact).
- The warranty will be void if:
a) the grinder has been tampered with;
b) the grinder has not been used according to this manual;
c) non-original and/or unauthorized parts, tools, or grinding wheels
have been fitted on the machine;
d) the grinder has been connected to voltage values other than the
one stated on the serial number plate.
- The warranty does not cover:
any mechanisms or parts affected by wear (such as the abrasive
disk/grinding wheel, the motor carbon brushes, vice, electrical
switches and adjustment devices/knobs).