Basic Operation - Toshiba MMY-MAP0804HT5P Manual Del Propietário

Ocultar thumbs Ver también para MMY-MAP0804HT5P:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

4

Basic operation

When you use the air conditioner for the first time or change the settings, follow the procedures below.
From next time, pushing the
button starts running of the air conditioner with the chosen settings.
Preparation
Turn on the power switch
When turned on, the separation line appears and
* The remote controller will not work for about 1 minute after turning on the power. This is not a
malfunction.
REQUIREMENT
Keep the power switch turned on during use.
When you resume using the air conditioner after a long period of disuse, turn on the power switch at least 12
hours before starting running.
Operations
TEMP.
ON / OFF
1, 3
2
TIMER SET
FAN
MODE
TIME
SAVE
VENT
FILTER
RESET
TEST
SET
CL
SWING/FIX
UNIT LOUVER
1
Push the
button.
The operation lamp lights up.
2
Push the "MODE
" button to select a
operation mode.
Each time you push the button, the operation
mode and its icon change in the following order:
Heat-pump model
Heat
Dry
Cool
Fan
(Dehumidify)
Cooling only model
Fan
Dry
Cool
(Dehumidify)
"
Dry" is not available for the concealed duct
high static type.
19-EN
1114208801.indd 10
1114208801.indd 10
blinks on the remote controller display.
3
Push the
button to stop running.
The operation lamp turns off.
Changing the fan speed
1
Push the "FAN
" button to select a fan
speed.
Each time you push the button, fan speed and
its indication change in the following order:
("
Auto" cannot be selected in the FAN
mode.)
Auto
High
Medium
Low
When heating, if the room does not heat up
using "
Low", select "
High" or
"
Medium".
The temperature sensor detects the return air
temperature at the indoor unit, which may
slightly differ from the actual room temperature
depending on installation condition. Set
temperature is a target of room temperature.
The fan speed selection function is not available
for the concealed duct high static type. Fan
speed is fixed and the indicator is fixed to
"
High".
Changing the set temperature
1
Push the "TEMP.
" buttons.
Push
to increase the temperature, and
decrease the temperature. (The set temperature
cannot be changed in the fan mode.)
NOTE
When cooling
Running starts in approximately 1 minute.
When heating
The air conditioner may continue running in the fan
mode for about 30 seconds after stopping heating.
The heated air comes out after a 3 to 5 minutes of
pre-heating with the indoor fan kept turned off. (The
pre-heat indicator
is displayed on the remote
controller.)
The fan speed becomes extremely low when the
room temperature has reached the set temperature.
However, for concealed duct high static types, the
fan speed does not change after the temperature
has reached to the set temperature.
– 10 –
Power save operation
to
Displayed
during Power
save operation.
TEMP.
ON / OFF
TIMER SET
FAN
MODE
Save button
TIME
SAVE
VENT
FILTER
RESET
TEST
SET
CL
SWING/FIX
UNIT LOUVER
1
Push the
button during operation.
Power save operation is activated.
is appeared.
2
Push
button to deactivate Power save
operation.
is disappeared.
NOTE
Capability of the air conditioner is saved during the
Power save operation. The room may not become
cool or warm enough.
Power save operation will not be deactivated by stop
operation, change operation mode or turn off the
power switch.
EN
20-EN
3/6/13 10:53 AM
3/6/13 10:53 AM

Hide quick links:

Publicidad

Tabla de contenido
loading

Tabla de contenido