Louver Direction - Toshiba MMY-MAP0804HT5P Manual Del Propietário

8

Louver direction

NOTE
To improve the cooling/heating performance, change
the louver angle for each operation.
The characteristics of air: Cool air falls, and warm
air rises.
CAUTION
Point the louver horizontally during cooling
If pointing downward for cooling, dew may form on the
surface of the air discharge or louver and may drop
down.
NOTE
If pointing horizontally for cooling, dew may form on
the surface of the cabinet or louver and may drop
down.
If pointing horizontally for heating, the room
temperature may be uneven.
Do not handle the louver manually.
Doing so may cause a failure.
Use the SWING/FIX button on the remote controller
to adjust the angle.
25-EN
1114208801.indd 13 1114208801.indd 13
4-way cassette type, 2-way
cassette type, 1-way cassette
type, ceiling type
To set the louver direction
1
Push the button during running.
SWING/FIX
The louver direction changes with each push of
the button.
For heating
Point the louver downward.
If not pointing downward, hot
air may not reach the floor.
Initial setting
For cooling
Point the louver horizontally.
If pointing downward, dew
may form on the surface of
the air discharge port and
Initial setting
may drop down.
For fan
Select a wind direction.
Initial setting
To start swinging
1
Push the SWING/FIX button repeatedly to set the
louver direction to the lowest position, then
push SWING/FIX again.
The SWING indicator is displayed and the
louver begins swinging.
In all operations
Repeat
– 13 –
To stop swinging
1
SWING/FIX
Push the button at the desired
position while the louver is swinging.
Push the SWING/FIX button repeatedly to change
the louver position again.
* However, even if the SWING/FIX button is pushed
while the louver is swinging, one of the
indications below may sometimes be displayed
and may not set the louver to the highest
position.
Indications when swinging is stopped
FAN/HEAT COOL/DRY
In this case, push the SWING/FIX button again after 2
seconds.
In COOL/DRY operation, the louver does not
stop as it directs downward. If stopping the
louver as it directs downward during swing
operation, it stops after moving to the third
position from the highest position.
Indications when swinging is stopped
FAN/HEAT COOL/DRY
operation operation
Unit select
When two or more indoor units are controlled with
one remote controller, the louver direction can be set
for each indoor unit by selecting them individually.
To set louver direction individually, push the
button (left side of the button) to display an indoor
unit number in the control group. Then set the louver
direction of the displayed indoor unit.
When no indoor unit number is displayed, all indoor
units in the control group can be controlled
simultaneously.
Each time you push the UNIT LOUVER (left side of the
button), the indication changes as follows:
No Unit No. Unit No.
display 1-1 1-2
Unit No. Unit No.
1-4 1-3
4-way cassette type only
To set the louvers individually
1
Push the UNIT LOUVER button (left side of the
button) during running to select a unit.
The unit number changes each time you push the
button.
Unit No. Unit No. Unit No.
1-1 1-2
No Unit No.
display 1-4
When no unit number is displayed, all units are
selected.
2
Push the UNIT LOUVER button (right side of the
button) to select a louver.
Each time you push the button, the indicator on the
left of the remote controller changes as follows:
No
display
* When no louver number is displayed, all 4
louvers are selected.
Louver No.
Electrical control box
03
Refrigerant
UNIT LOUVER
pipe
04
Drain pipe
01
1-3
02
26-EN
3/6/13 10:53 AM 3/6/13 10:53 AM