Publicidad
Idiomas disponibles
Idiomas disponibles
GAS FLOW
SYMPTOM
• Grill does not reach desired temperature or heats unevenly.
• One or more of the burners fail to ignite.
• Flame is low when burner is on high position.
• Flames do not run the whole length of the burner.
• Burner flame pattern is erratic.
CAUSE
The "flow limiting device" has been activated.
This safety feature built into the regulator restricts
the gas flow in the event of a gas leak. You can
inadvertently activate this safety feature without
having a gas leak. This typically occurs when you
turn on the gas at the LP tank and one or more of the
control knobs are not in the off position. It may also
occur if you turn on the LP tank too quickly.
The LP tank is low or empty.
Fuel hose is bent or kinked.
Burner ports are dirty.
SYMPTOM
• Gas is smelled in conjunction with burner flames that appear yellow and lazy.
CAUSE
Spider screens on the burners are obstructed.
SYMPTOM
• The smell of gas and/or a light hissing sound.
CAUSE
The internal rubber seal in the LP tank valve could be
damaged.
GREASY GRILL (Peeling Paint & Flare-Ups)
SYMPTOM
• Inside of lid appears to have the appearance of peeling paint.
CAUSE
The flakes you see are accumulated cooking vapors
that have turned into carbon.
SYMPTOM
• Experiencing flare-ups when grilling or preheating.
CAUSE
There is leftover food from the previous meal.
The inside of the grill needs to be cleaned thoroughly.
WARNING: Do not attempt to make any repair to gas carrying, gas burning, ignition components or
m
structural components without contacting Weber-Stephen Products LLC, Customer Service Department.
WARNING: Failure to use genuine Weber-Stephen parts for any repair or replacement will void all
m
warranty protection.
m
CAUTION: The burner tube openings must be positioned properly over the valve orifices.
59502_Spt_II_LP_enUS_esMX_frCA_working.indd 17
SOLUTION
Reset the "flow limiting device" by closing the LP
tank valve and turning all the burner control knobs
to the off
position. Wait five minutes to allow
accumulated gas to dissipate, then ignite the grill
again following the instructions in the "Operation"
section.
Refill LP tank.
Straighten fuel hose.
Clean burner ports. Refer to "Cleaning the
Burner Ports."
SOLUTION
Clean spider screens. Refer to "Cleaning the Spider
Screens" in the Product Care section. Also refer to
the illustrations and information in this section about
proper flame pattern and spider screens.
SOLUTION
Inspect the rubber seal for damage. If damaged,
return tank to local retailer.
SOLUTION
This happens over time after repeated use of your
grill. This is not a defect. Clean the lid. Refer to the
"Product Care" section.
SOLUTION
Always preheat the grill on the highest setting for 10
to 15 minutes.
Follow the steps in the "Cleaning and Maintenance"
section to clean the grill inside from the top down.
Proper Burner Flame Pattern
The burners in your grill were factory set for the
correct air and gas mixture. When the burners
are performing correctly, you will see a specific
flame pattern. The tips may occasionally flicker
yellow (A), with a descending light blue (B) to
dark blue flame (C).
WARNING: Blocked and dirty ports can
m
restrict full gas flow, resulting in a fire (D) in
and around the gas valves, causing serious
damage to your grill.
D
Spider Screens
The combustion air openings of the burners (E)
are fitted with stainless steel screens to
prevent spiders and other insects from spinning
webs and building nests inside the burners.
Additionally, dust and debris can accumulate
on the outside of the spider/insect screen and
obstruct the oxygen flow to the burners.
E
CALL
CUSTOMER
SERVICE
If you are still experiencing any
problems, contact the Customer Service
Representative in your area using
the contact information on
weber.com.
A
B
C
17
11/13/17 11:24 AM
Publicidad
