Publicidad
Notes on Safety
Instructions for installation and connection
Disconnect the battery ground wire during installation and connection.
When drilling a hole, be sure not to damage any vehicle part (battery,
cable, fuse, etc.).
The positive cable must have a cross-section of at least 2,5 mm
is protected by a quick-acting fuse of 10 A. Do not use the positive cable
installed ex factory.
The side panel of the car radio heats up considerably during
operation.
Attention: Pay attention that the cables do not contact with the
housing.
Note:
By means of the support included in the delivery you can mount the set
in cars with a DIN car radio cut-outout of 182 x 53 mm, an installation
depth of 165 mm and an instrument panel thickness around the fixing
clips of 1 - 20 mm, see fig. 1.
For cars with other cut-out dimensions Blaupunkt delivers car-specific
installation kits for common car types for 50/52 mm sets.
Please check the dimensions and, if necessary, use a car-specific
installation kit, e. g. VW Golf II / Jetta II/: 7 608 3824 73.
When using installation sets for units of 52 mm four distance plates, order
number 8 601 055 056, must be used, fig. 1a.
Preparation of car radio installation
Install the car radio into the DIN cut-out provided in your car's dashboard
ex factory.
Prepare the car radio DIN cut-out (unlock shelf or dummy cover) or cut
out the car radio compartment to 182 x 53 mm.
Grasp behind the car radio cut-out and check how many of the fixing
strips of the car radio support can be bent.
Note:
Try to bend as many fixing strips as possible.
Insert the support into the cut-out and bend the appropriate fixing strips
with a screwdriver, see fig. 1, 2.
Connection
Use the adapter cable enclosed to the CD-Changer or the Connecting
block.
Connection overview .................................................................... fig. 4
Notes on connection ..................................................................... fig. 5
Connection of equalizer and amplifier .......................................... fig. 6
Connection of CD-Player .............................................................. fig. 7
Loudspeaker connection:
4 speakers (4 Ω/20 W) .................................................................. fig. 8
Impotant notes!
If these notes are disregarded, there is danger of destroying the
final stages.
Do not connect speaker outputs to ground!
Connection with QuickOut installed ex factory
If your car is fitted with a QuickOut ex factory (at present Opel), the
QuickOut ex factory has to be removed.
Car radio installation
Insert the car radio from the front into the support and push in until the
stop springs on the sides engage right and left (distinct click to be heard).
Removal of the car radio
Insert the brackets right and left into the provided trimplate holes and
push in until you hear a distinct click (lateral springs are unlocked).
Using both brackets (see fig. 3), pull the unit out.
Note
Locked brackets can only be removed after taking out the unit.
GB
QuickOut (shuttle support)
Use the car radio specific QuickOut support.
Notes on connection, fig. 5
Ground cable
Do not connect the ground cable to the negative pole of the battery.
Route the ground cable to a suitable ground point (car body screw, car
2
. The unit
body metal sheet) and shorten it accordingly.
Remove the insulation from the ground cable and attach the forked cable
lug (if necessary, solder it).
Scratch off the paint from the contact area of the ground point and
lubricate it with graphite grease (important for good ground contact).
Screw on the ground cable.
Positive cable (ACC + 12 V) (ignition)
Do not use the positive cable installed in the car.
Route the positive cable (thick red cable of 2.5 mm
route the cable near the cable harnesses). Connect the fuse holder to
protect the positive cable and connect it to the positive pole of the battery
(if necessary, drill a hole into the fire wall and use cable ducts).
Note:
Upon customer request and if the car radio system is operated via the
ignition, the switched positive line, installed ex factory, can be connected
to a relay (Bosch part no. 0 332 014 125).
Permanent plus connection (Battery +12 V)
Connect the permanent plus terminal together with the cable and cable
clamp to a fuse-protected positive line (e.g. clock, warning flasher).
Control cable (Power Antenna +)
When connecting a fully automatic motor antenna, use the cable clamp
to fasten the control cable of the motor antenna to the control cable.
Modifications reserved
Notes de sécurité
Instructions de montage et de branchement
Pendant le montage et le branchement des appareils, il convient de
déconnecter le pôle négatif de la battérie.
Veiller à ce qu'aucun élément de voiture (tel que la battérie, les câbles,
les porte-fusibles) ne soit endommagé par le perçage des trous).
La section du câble positif ne doit pas être inférieure à 2,5 mm
est protégé par l'intermédiaire d'un fusible à déclenchement rapide 10 A.
Ne pas utiliser le câble positif installé de l'usine.
Le panneau latéral de l'autoradio s'échauffe considérablement
pendant l'opération.
Attention: Alors faire attention qu'aucun câble ne touche le boîtier.
Note:
A l'aide du support inclus dans le jeu de montage vous pouvez monter
le poste dans des voitures qui disposent d'une découpe DIN de 182 x 53
mm, d'une profondeur de 175 mm et d'une épaisseur du tableau de bord
de 5,2 - 6,3 mm autour des éclisses de montage, voir fig. 1.
Blaupunkt livre des jeux de montage spéciaux pour les voitures courantes
avec des découpes différentes pour les appareils 50/52 mm.
Veuillez donc vérifier les mesures de la découpe de votre voiture et, si
nécessaire, commander un jeu de montage spécial, p. ex. VW Golf II /
Jetta II: 7 608 3824 73.
En utilisant des jeux d'installation pour des postes de 52 mm il faut utiliser
4 plaques de distance, numéro de référence 8 601 055 056, fig. 1a.
+12V
2
) to the battery (do not
per. +12V
+12V
F
2
. L'appareil
Publicidad
