Olimpia splendid MIA 7,5 Instrucciones Para La Instalación, Uso Y Mantenimiento página 15

GB
300300
• Do not place objects in in ammable material or any material that can compromise
the operation of the stove on the stove or within the safety distance;
• In addition, it is advisable to keep all elements of combustible or in ammable material
such as beams, wooden furniture, drapes, in ammable liquids, etc. outside the ra-
diance area of the stove, and in any case at least 1 m from the heating block (Fig. 8);
Carefully read the precautions and follow the procedures correctly.
• In case of connection to wooden walls or other in ammable material, it is necessary
to insulate the smoke discharge tube with ceramic bre or another material with the
WARNING!
same characteristics.
In case of breakage or poor functioning contact the Authorized Assistance Cen tre;
any attempt to remove parts or perform maintenance on the device can expose the
user to electrical shock danger.
The stove contains parts whose maintenance must be done by qualified personnel.
The stove is a heating device; its parts reach extreme temperatures and contact wi-
thout adequate protection can provoke burns of various degrees.
Pay particular attention to children.
Do not insert ngers or other objects in the air ow exit slits.
Inside the device there is a high speed fan that could cause grave personal injury.
Pay particular attention to children.
Do not remain for long periods directly exposed to the ow of hot air. Direct and pro-
longed exposition to the cold air could be hazardous to health.
Pay particular attention in rooms where there are children, the elderly or the ill. In case
the stove functions poorly, shut down the device immediately and contact the Autho-
rized Assistance Centre.
The continued use of the device in said conditions can cause res or ashes.
Fig. 8: minimum distance of objects
Minimum aeration for comburant air intake
For a correct and safe placement of the air intake all the measures and prescriptions
(Fig. 9) must be respected.
There are distances to respect to prevent the comburant air from being subtracted from
another source: for example the opening of a window could cause eddies in the outside
air subtracting it from the stove.
Norms and conformity declarations
Legislation
• Our company declares that the stove conforms to the following norms for EC European
Directive marking.
• 2004/108 EC (EMC directive) and successive amendments.
• 2006/95 EC (low voltage directive) and successive amendments.
• Regulation of the CPR (EU 305/2011).
• For installation in Italy refer to the UNI 10683/98 or successive modi cations; the te-
chnician installing the hydrothermal sanitary system will issue the declaration of con-
formity according to L. 37/2008. The installation of appliance has to be in accordance
with local and national laws and with European norms.
• EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3; EN 60335-1;
EN 60335-2-102; EN 62233; EN 14785; EN 50581.
Responsibility
The manufacturer declines every direct or indirect, civil or penal responsibility due to:
• Poor maintenance.
• Failure to observe the instructions contained in the manuals.
Fig. 9: distance from walls
• Use in non-conformity with the safety directives.
• Installation in non-conformity with the norms in force in the country.
Lighting
• Installation by unquali ed or untrained personnel.
• Modi cations and repairs not authorized by the manufacturer.
• Before lighting the stove, carefully read the use and maintenance manual.
• Use of non-original replacement parts.
• Remove from the tank all the tools that were inserted during packaging and be sure
• Exceptional events.
that the tank is free of eventual extraneous bodies.
Use of unsuitable pellets
•
• Unroll the environmental probe placed on the rear of the stove, without placing it on
the heated parts of the stove.
• Correctly connect the pellet stove to the ue.
Installation
• Fill the tank with 6mm diameter pellets.
Flue
• Open the door and check that the basket is properly inserted in its slot and that the
ame trap is located in the upper part of the combustion chamber.
The ue must meet the following requirements:
• Close the door. Never open the door while the pellet stove is operating.
• No other type of chimney, stove, boiler or hood vent must be connected ( g.1).
• Connect the stove to an outlet with the appropriate cable received with the stove.
• It must be adequately distanced from combustible or in ammable material by means
• Place the switch on the rear of the stove at the "1" position.
of an air cavity or opportune insulation.
• Press the ON/OFF key for 2 seconds and the gearcase will begin its lighting cycle.
• The internal section must be uniform, preferably circular: the square or rectangular
sections must have rounded corners with a radius of no less than 20 mm, a maximum
relationship between the sides of 1.5; the walls as smooth as possible with no narro-
ATTENTION:
wed sections, regular curves and no discontinuities, with deviations from the axis not
During the rst lighting it is necessary to ventilate the environment well, since
more than 45°.
during the rst hours of operation unpleasant odours could develop due to fumes
• Every device must have its own ue with a diameter equal to or larger than the stove's
from the paint and the grease in the tuyère wrapping.
smoke clearing tube and a height not less than that declared.
• Never use two stoves, a chimney and a stove, a stove and a wood kitchen, etc in the
If during the normal operation of the stove, the temperature of the smoke reaches 220°C
same environment, since the draught of one could damage the draught of the other.
(parameter which can be modi ed by a technician) the smoke is modulated as follows:
• Collective type ventilation ducts that can lower the atmospheric pressure in the in-
• Smoke removal motor set at the maximum speed;
Installation manual
• Pellet loading gear motor at the minimum speed;
• Tangential heat exchange fan at the maximum speed.
This procedure functions to lower the temperature of the smoke. When this returns below
the level of 220°C the stove will restore the speed of the three motors returning them
to the settings before the level was passed.
If the electrical current cuts out, once it is restored, the display will indicate a state of
anomaly and will read "Fire cool" ( ame present). The suction will be increased to expel
the residual smoke.
Operations to be performed by the Authorized Assistance Centre
During the stove installation operation, keep children out of the work area to avoid
every season before the lighting
unforeseen accidents.
Do not block or cover in any way the body of the stove or obstruct the slits placed on
• A general cleaning inside and outside.
the upperside.
• A careful cleaning of the tubes.
Obstructing said slits can cause res.
• A careful cleaning and disincrustation of the crucible and the relative cavity.
Do not use the stove in areas containing precision devices or works of art.
• Clean the motors, checking the play and fastenings of the mechanisms.
The quality of the conserved objects may deteriorate.
• Clean the smoke channel (substitute the tube gaskets) and smoke extractor fan ca-
Do not expose animals or plants to direct air ow from the unit.
vity.
Prolonged direct exposition to the ow of air from the stove can have negative effects
• Clean pressure switch, sostitute silicone tube.
on plants and animals.
• Check the probe.
Occasionally ventilate the room during the use of the device.
• Clean, inspect and disincrust the lighting resistor compartment, replacing it if neces-
Insuf cient ventilation can be the origin of insuf cient oxygen in the room.
sary.
Do not expose the stove to contact with water.
• Clean/check the synoptic panel.
The electrical insulation could be damaged, with the consequent possibilities of elec-
• Visually inspect the electrical cables, the connections and the electrical power cable.
trocution and breakage due to the thermal extremes.
• Clean the pellet container and verify the play with the screw feeder gear motor.
Verify the installation conditions to locate eventual damage.
• Replace the door seals.
After the stove has completed 900 hours of operation (the lower screen will read
• Test functions, loading the screw feeder, lighting, 10 minutes of operation and shut
"SErV"), contact the Authorized Assistance Centre for cleaning and ordinary mainte-
down.
nance.
• Check the electrical parts and the electronic components.
Do not use in ammable gas near the stove.
Unhook the automatic switch if the device will not be used for long periods of time.
We check the start up of all our stoves.
WARNING
• Use of this device is subject to all local and national regulations as well as European
regulations.
• The installation of this device is subject to all local and national regulations as well as
Combustion European regulations.
stallation environment are not permitted, even if installed in environments that are ad-
air inlet
• Do not pour the Pellets directly into the brazier jacent to and communicating with the locale of the installation.
• It is forbidden to make xed or mobile openings in the ue to connect devices different • To load the Pellets, open the tank lid positioned on the upper part of the stove and ca-
refully empty the Pellets' package inside.
from that for which it is originally intended.
• It is forbidden to pass other air feeding channels or tubes for electrical system usage • Before pouring the Pellets inside the tank, please make sure that the stove is turned
through the ue, even if oversized. off.
• Should the stove overheat, a safety device will engage and block the feeder mecha-
• It is advisable that the ue be furnished with a chamber which collects solid material
nism. After the stove's cool-down cycle has been completed, re-engage the thermostat
and eventual condensation situated below the vertical entrance to the ue so that it
placed at the back of the stove, by removing the thermostat's cap and pressing the
button underneath. In case of repeated malfunctions, please contact authorized te-
chnical support.
Walls
• The device is not intended for users (children included) whose physical or mental abi-
lities are reduced or by users who lack the proper knowledge or experience, unless
NO
they have been instructed by a person responsible of their safety on the proper use of
this device and all the security measures. Children have to be supervised so that they
do not play with the device.
• Use only Pellets recommended by the manufacturer, of a diameter not exceeding 6mm
and a length not exceeding 30mm.
• Please store the Pellet in a dry environment.
13 14 11
WARNING!
NO
Thermostat's cap
YES
Fig.1: methods for installing the ue
GB