Skil 1011 Manual Original página 10

6 Incorrect polarity of the charger connection could cause a
hazard (only charge the battery with the charger supplied)
7 Automatic shut-off when charger gets too hot (thermic
fuse blows and charger becomes useless)
8 Do not dispose of the charger together with household
waste material
9 Do not dispose of the battery together with household
waste material
0 Insulation class III
! IP20 (degree of protection against dust and humidity)
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of the charger to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of the
charger, it must be disposed of safely and not left
unattended
USE
• Charging battery @
- battery of new tools is not fully charged
- connect charger to power source as illustrated
- insert battery into charger
- red light K will turn on indicating that the battery is
being charged
- red light K will stay on as long as the battery is
connected to the charger and the charger is in the wall
socket
! remove battery from charger after charging
period has ended thereby lengthening the service
life of the battery
IMPORTANT:
- after 3-5 hours the charging operation will be
completed, and the battery may be used
- while charging, the charger and the battery may
become warm to touch; this is normal and does not
indicate a problem
- ensure that the outside surface of the battery is clean
and dry before inserting into charger
- do not charge at temperatures below 0°C and over
45°C; this will seriously damage the battery as well as
the charger
- do not remove battery from tool while it is running
! a battery that is new or has not been used for a
longer period does not develop its full capacity
until after approximately 5 charging/discharging
cycles
- do not repeatedly recharge the battery after only a few
minutes of operation; this may result in a reduction of
operating time and battery efficiency
- if you anticipate long periods of non-use for the tool, it
is best to unplug the charger from its power source
• On/Off #
• Speed control for smooth starting $
• Changing direction of rotation %
- when not properly set in left/right position, switch A 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
• Changing bits ^
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
• Torque control (VariTorque) &
- output torque will increase as clutch ring D is rotated
from 1 to 11; position E will lock up the clutch to permit
drilling or driving heavy duty work
- when turning in a screw, first try VariTorque position 1
and increase until the desired depth has been reached
• Mechanical gear selection *
- set selector F to desired speed
! actuate the gear selector while tool is running slowly
1 = LOW SPEED
- high torque
- for screwdriving and drilling large diameters
- for tapping thread
2 = HIGH SPEED
- lower torque
- for drilling small diameters
• Spot light G (
Spot light G automatically lights on when activating
switch A 2
• Holding and guiding the tool )
! while working, always hold the tool at the
grey-coloured grip area(s)
- keep ventilation slots H 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
• Torch ¡
APPLICATION ADVICE
• Use the appropriate bits ™
! only use sharp bits
• When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
• When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking of
the wood
• For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
• When screwdriving in hard wood one should pre-drill a hole
• Splinterfree drilling in wood £
• Dustfree drilling in walls ≤
• Dustfree drilling in ceilings ∞
• Drilling in tiles without skidding §
• For more tips see www.skil.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Only use replacement batteries of the correct type (SKIL
spare part number 2610Z03258)
• Keep tool and charger clean
- clean charging contacts in charger with alcohol or
contact cleaner
! unplug charger from power source before cleaning
• If the tool/charger should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on www.skil.com)
10