Stanley FATMAX SFMCCSB664 Traducido De Las Instrucciones Originales página 10

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 84
English
Chainsaw Names and Terms
Bucking - The process of cross cutting a felled tree or log into lengths.
Motor Brake - A device used to stop the saw chain when the
trigger is released.
Chain Saw Powerhead - A chain saw without the saw chain
and guide bar.
Drive Sprocket or Sprocket - The toothed part that drives the
saw chain.
Felling - The process of cutting down a tree.
Felling Back Cut - The final cut in a tree felling operation made
on the opposite side of the tree from the notching cut.
Front Handle - The support handle located at or toward the
front of the chain saw.
Front Hand Guard - A structural barrier between the front
handle of a chain saw and the guide bar, typically located
close to the hand position on the front handle.
Guide Bar - A solid railed structure that supports and guides
the saw chain.
Guide Bar Scabbard - Enclosure fitted over guide bar to prevent
tooth contact when saw is not in use.
Kickback - The backward or upward motion, or both of the guide
bar occurring when the saw chain near the nose of the top area
of the guide bar contacts any object such as a log or branch, or
when the wood closes in and pinches the saw chain in the cut.
Kickback, Pinch - The rapid pushback of the saw which can
occur when the wood closes in and pinches the moving saw
chain in the cut along the top of the guide bar.
Kickback, Rotational - The rapid upward and backward
motion of the saw which can occur when the moving saw
chain near the upper portion of the tip of the guide bar
contacts an object, such as a log or branch.
Limbing - Removing the branches from a fallen tree
Low-Kickback Chain - A chain that reduces the kickback
performance requirements. (when tested on a representative
sample of chain saws.)
Normal Cutting Position - Those positions assumed in
performing the bucking and felling cuts.
Notching Undercut - A notch cut in a tree that directs the tree's fall.
Rear Handle - The support handle located at or toward the rear
of the saw.
Reduced Kickback Guide Bar - A guide bar which has been
demonstrated to reduce kickback significantly.
Replacement Saw Chain - A chain that reduces the kickback
performance requirements when tested with specific
chain saws.
Saw Chain - A loop of chain having cutting teeth, that cut the
wood,and that is driven by the motor and is supported by the
guide bar.
Ribbed Bumper - The ribs used when felling or bucking to pivot
the saw and maintain position while sawing.
Switch - A device that when operated will complete or interrupt
an electrical power circuit to the motor of the chain saw.
Switch Linkage - The mechanism that transmits motion from a
trigger to the switch.
8
Switch Lockout - A movable stop that prevents the
unintentional operation of the switch until manually actuated.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
Impairment of hearing.
Risk of personal injury due to flying particles.
Risk of burns due to accessories becoming hot
during operation.
Risk of personal injury due to prolonged use.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of your mains.
Your STANLEY FATMAX charger is double insulated
in accordance with EN60335; therefore no earth wire
is required.
If the
supply cord is damaged, it must be replaced by a specially
prepared cord available through the STANLEY FATMAX
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in the plug.
Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1 mm
is 30 m.
When using a cable reel, always unwind the cable completely.
SAVE THESE INSTRUCTIONS
Chargers
STANLEY FATMAX chargers require no adjustment and are
designed to be as easy as possible to operate.
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for compatible battery
chargers (refer to Technical Data).
Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
battery pack.
; the maximum length
2

Publicidad

Tabla de contenido
loading

Tabla de contenido