DeWalt DW716 Manual De Instrucciones página 16

5. Secure the material before cutting. Cut slowly through
the material. Failure to clamp securely or cut slowly could
result in the material coming loose and causing injury.
After several cuts are made at various miter angles other
than 0º, the platform may weaken and not properly support
the work. Install a new, unused platform to the saw after
presetting the desired miter angle.
CAUTION: Continued use of a platform with several kerfs
may cause loss of material control and possible injury.
Removing and Replacing Belt
The belt is designed to last the life of the tool. However,
abuse of the tool could cause the belt to fail.
If the blade does not turn when the motor is running, the
belt has failed. To inspect or replace the belt, remove the belt
cover screws. Remove the belt cover. Inspect the ribs of the
belt for wear or failure. Check belt tension by squeezing the
belt as shown in Figure 23. The belt halves should almost
touch when squeezing firmly with the thumb and index finger.
To adjust the tension, loosen, but do not remove, the four
Phillips head screws shown. Then rotate the set screw on
the top of the motor plate casting until the proper tension is
achieved. Tighten the four screws securely and replace the
belt cover.
NOTE: Over tightening the belt will cause premature motor
failure.
MAINTENANCE
DO NOT use lubricants or cleaners (particularly spray or
aerosol) in the vicinity of the plastic guard. The polycarbonate
material used in the guard is subject to attack by certain
chemicals.
1. All bearings are sealed. They are lubricated for life and
need no further maintenance.
2. Periodically clean all dust and wood chips from around
AND UNDER the base and the rotary table. Even though
slots are provided to allow debris to pass through, some
dust will accumulate.
3. The brushes are designed to give you several years
of use. If they ever need replacement follow the
instructions under Brushes or return the tool to the
nearest service center for repair.
Service Information
Please have the following information available for all service
calls:
Model Number ____________________________ Type_____
Serial Number _______________ _______________________
Date and Place of Purchase ___ _______________________
FIG. 21
FIG. 22
SCREWS
(two each
side)
SET
SCREW
FIG. 23
SCREWS
14
Repairs
To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment (including brush inspection
and replacement) should be performed by authorized service
centers or other qualified service organizations, always using
identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRANTY SERVICE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• CONFIRMATION OF OWNERSHIP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof of purchase.
• FOR YOUR SAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to faulty
E
materials or workmanship for three years from the date of
purchase. This warranty does not cover part failure due to
normal wear or tool abuse. For further detail of warranty
coverage and warranty repair information, visit www.dewalt.
com or call 1-800-4-D WALT (1-800-433-9258). This
E
warranty does not apply to accessories or damage caused
where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
In addition to the warranty, D WALT tools are covered by our:
E
1 YEAR FREE SERVICE
D WALT will maintain the tool and replace worn parts
E
caused by normal use, for free, any time during the first year
after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of
your D WALT Power Tool, Laser, or Nailer for any reason,
E
you can return it within 90 days from the date of purchase
with a receipt for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-800-4-D
(1-800-433-9258) for a free replacement.
Please refer to the beginning of the manual for labels.
WALT
E