Publicidad
Idiomas disponibles
Idiomas disponibles
5. First, wind new line in the channel of the spool closest to
the holding slots
39
as shown in figure Q.
6. Place the end of the cutting line
hole
41
.
7. Wind the cutting line onto the spool in the direction of the
arrow on the bottom of the spool.
8. When the wound cutting line reaches the beginning of the
holding slots, cut the line approximately 106 mm.
9. Push the line in the holding slots on one side of the spool to
hold the first line while you wind the second line.
10. Repeat the above procedure for the second cutting line on
the lower section of the spool.
CAUTION: Before you begin trimming, only use the
appropriate type of cutting line. Ensure that cutting line is
present in both sections of the spool as shown in Figure R.
11. Once both lines are wrapped around the spool
your thumb and finger on the holding slots to further secure
the string and feed the end of each line through the two
holes
on either side of the head in the spool housing
43
12
as shown in figure S.
12. Line up the white nubs
37
the recesses
42
of the spool. Align the holding slots
with the two holes
as close as possible.
43
13. Push the spool into the spool housing and turn
counterclockwise to lock the spool in place. Ensure the
white nub
37
appears in the spool window
the line doesn't unravel and wrap around the shaft below
the spool.
14. Pull both ends of the cutting line to release them from the
holding slots. If the line extends past the cutting blade on the
guard cut the line so it just reaches the blade.
MAINTENANCE
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
1. Keep the air intake slots
44
avoid overheating.
2. Your trimmer line can dry out over time. To keep your line in
top condition, store spare line in a plastic, sealable bag with
a tablespoon of water.
3. Plastic parts may be cleaned by using a mild soap and a
damp rag.
4. The line cutter on the edge of the guard can dull over time.
It is recommended you periodically touch-up the sharpness
of the blade with a file.
The charger and battery pack are not serviceable.
40
into the retaining
36
, place
inside the spool housing with
39
38
. Make sure
, shown in figure T, clean to
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
•
Run the battery pack down completely, then remove it from
the tool.
•
Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
EngLIsh
WALT recommended
e
35
Publicidad
