Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
d. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
6. Service
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
make sure that the safety of the power tool is maintained.
Additional power tool safety warnings
Warning! Additional safety warnings for the
!
Alligator
Lopper.
TM
10
Warning! Never use the tool above shoulder height.
Always position yourself out of the path of falling
branches and debris.
Warning! Do not use this tool to fell trees.
Keep all parts of your body and clothing away from the
saw chain at all times. Hold the tool in front of you and
be aware of the saw chain position especially when
cutting branches near the ground. Before you switch on
make sure the saw chain is not contacting anything.
Pre-plan a safe exit from falling branches and debris.
Ensure the exit route is clear of obstacles that would
prevent or hinder movement. Remember wet grass and
freshly cut bark is slippery.
Be aware of the direction that a branch may fall.
Consider all conditions that may affect the direction of
fall, including:
- The intended direction of fall.
- The natural lean of the branch.
- Any unusual heavy limb structure or decay.
- Surrounding trees and obstacles including
overhead lines.
- The wind speed and direction.
The safe distance between a branch and debris to be
felled and bystanders, buildings and other objects is at
least 2 1/2 times the length of the branch. Any
bystander, building or object within this distance is at
risk from being struck by the falling branch.
When cutting a limb that is under tension, be aware of
spring-back. When the tension in the wood fibres are
released the spring loaded limb may strike the operator
and/or throw the tool out of control.
Always wear suitable safety equipment such as non-
skid safety shoes, hard hat, goggles, ear protection and
gloves when operating the tool.
Ensure someone is nearby (at a safe distance) in case
of an accident.
Do not attempt to operate the tool when in a tree, on a
ladder or standing on any other unstable support.
Keep proper footing and balance at all times.
Hold the tool firmly with both hands when the motor is
running.
Keep handles dry, clean and free from oil and grease.
Greasy oily handles are slippery causing loss of control.
Do not let the moving chain contact any object at the tip
of the guide bar.
Keep your saw chain properly tensioned. Check tension
at regular intervals with the motor stopped and cord
disconnected.
Begin and continue cutting only with the chain moving at
full speed.
Publicidad
Tabla de contenido
