DeWalt DW706 Manual De Instrucciones página 27

Safety instructions
When using stationary power tools, always observe the safety
regulations applicable in your country to reduce the risk of fire,
electric shock and personal injury.
Read all of this manual carefully before operating the tool.
Save this manual for future reference.
General
1 Keep work area clean
Cluttered areas and benches can cause accidents.
2 Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or wet
conditions. Keep the work area well lit (250 - 300 Lux). Do not use the
tool where there is a risk of causing fire or explosion, e.g. in the
presence of flammable liquids and gases.
3 Keep children away
Do not allow children, visitors or animals to come near the work area or
to touch the tool or the mains cable.
4 Dress properly
Do not wear loose clothing or jewellery, as these can be caught in
moving parts. Wear protective hair covering to keep long hair out of the
way.
When working outdoors, preferably wear suitable gloves and non-slip
footwear.
5 Personal protection
Always use safety glasses. Use a face or dust mask whenever the
operations may produce dust or flying particles. If these particles might
be considerably hot, also wear a heat-resistant apron. Wear ear
protection whenever the sound level seems uncomfortable, i.e. if the
sound pressure stated in this manual exceeds 85 dB(A).
6 Guard against electric shock
Prevent body contact with earthed or surfaces (e.g. pipes, radiators,
cookers and refrigerators).
When using the tool under extreme conditions (e.g. high humidity, when
metal swarf is being produced, etc.), electric safety can be improved by
inserting an isolating transformer or a (FI) earth-leakage circuit-breaker.
7 Do not overreach
Keep proper footing and balance at all times.
8 Stay alert
Watch what you are doing. Use common sense. Do not operate the
tool when you are tired.
9 Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it frees both
hands to operate the tool.
10 Connect dust extraction equipment
If devices are provided for the connection of dust extraction and
collection facilities, ensure that these are connected and properly used.
11 Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed from the
tool before operating the tool.
12 Extension cables
Before use, inspect the extension cable and replace if damaged.
When using the tool outdoors, only use extension cables intended for
outdoor use and marked accordingly.
13 Use appropriate tool
The intended use is described in this instruction manual.
Do not force small tools or attachments to do the job of a heavy-duty
tool. The tool will do the job better and safer at the rate for which it was
intended. Do not force the tool.
Warning! The use of any accessory or attachment or performance of
any operation with this tool other than those recommended in this
instruction manual may present a risk of personal injury.
14 Check for damaged parts
Before use, carefully check the tool and mains cable for damage.
19
Check for misalignment and seizure of moving parts, breakage of
parts, damage to guards and switches and any other conditions that
may affect its operation. Ensure that the tool will operate properly and
perform its intended function. Do not use the tool if any part is
damaged or defective. Do not use the tool if the switch does not turn it
on and off. Have any damaged or defective parts replaced by an
authorised D WALT repair agent. Never attempt any repairs yourself.
E
15 Unplug tool
Switch off and wait for the tool to come to a complete standstill before
leaving it unattended. Unplug the tool when not in use, before changing
any parts of the tools, accessories or attachments and before
servicing.
16 Avoid unintentional starting
Be sure that the tool is switched off before plugging in.
17 Do not abuse cord
Never pull the cord to disconnect from the socket. Keep the cord away
from heat, oil and sharp edges.
18 Store idle tools
When not in use, tools must be stored in a dry place and locked up
securely, out of reach of children.
19 Maintain tools with care
Keep the tools in good condition and clean for better and safer
performance. Follow the instructions for maintenance and changing
accessories. Keep all handles and switches dry, clean and free from oil
and grease.
20 Repairs
This tool is in accordance with the relevant safety regulations. Have
your tool repaired by an authorised D
should only be carried out by qualified persons using original spare
parts; otherwise this may result in considerable danger to the user.
Additional safety rules for mitre saws
21 Guard actuation
The blade guard on your saw will automatically raise when the arm is
brought down; it will lower over the blade when the arm is raised. The
guard can be raised by hand when installing or removing saw blades or
for inspection of the saw. Never raise the blade guard manually unless
the saw is switched off.
22 Flying debris
The front section of the guard is louvred for visibility while cutting.
Although the louvres dramatically reduce flying debris, there are
openings in the guard and safety glasses should be worn at all times
when viewing through the louvres.
23 Saw blades
Make sure that the blade rotates in the correct direction. Keep the
blade sharp. Do not use blades of larger or smaller diameter than
recommended. For the proper blade rating refer to the technical data.
24 Blade guards
Never operate the saw without the guards in place.
25 Mind your hands
Keep your hands out of the path of the saw blade. Never place them in the
blade area when the saw is connected to the electrical power source.
26 Stopping the motor
Raise the blade from the kerf in the workpiece prior to releasing the
switch. Never attempt to stop the machine in motion by jamming a tool
or similar against the blade. Do not wedge anything against the fan to
hold the motor shaft.
27 Maintenance of the blade and the arbor collars
Make sure that the blade and the arbor collars are clean on the
surfaces of contact and use the supplied wrench to tighten.
Environmental temperature
Only use the machine at ambient temperatures from 5 °C to 40 °C.
E N G L I S H
WALT repair agent. Repairs
E
en - 2