08_Led Lights; 09_Power Sensor Calibration; 10_Cadence Sensor; 11_Heart Rate Monitor - Elite DIRETO XR Instrucciones

With the exception of smartphones that feature integrated
ANT+ connectivity, a USB dongle is necessary to connect
via the ANT+ protocol.
An ANT+ flash drive is required when using Android, PC
Windows and Mac devices. It's available for purchase on
the www.shopelite-it.com website or via other channels –
it's required to connect the device to the hometrainer via
the ANT+ protocol.
An OTG adapter cable is required for Android devices, while
iOS devices require a specific flash drive (not included)
compatible with the 30-pin iOS connector.
A complete list of ANT+ compatible devices is available at:
http://www.thisisant.com/directory/
* Warning: should the software / app / device employ the
Speed&Cadence protocol to detect speed, you must set a
wheel circumference value that equals the actual wheel
value divided by 12,1. For instance, if wheel circumference
is 2095mm, the value to input as circumference is 2095 /
12,1 = 173mm.
Wireless specifications:
Transmission frequencies: 2400 to 2483.5 MHz
Protocols: Bluetooth 4.0 & ANT+
Transmission distance in the open: 10m
ANT+ transmission power: 4dB
Bluetooth transmission power: 0dB

08_LED LIGHTS

DIRETO XR transmits speed, cadence and power data via
the ANT+ and Bluetooth Smart protocols.
There are 3 LED lights on the motherboard, displaying
power supply status, motherboard status and the protocol
being used.
The LED lights come in 3 colors with the following
meanings:
Red = status of hometrainer power supply
- Off = DIRETO XR is not receiving power or has the entered
sleep mode
- On = DIRETO XR is powered up.
Blue = DIRETO XR is connected via the Bluetooth Smart
protocol.
- Blinking = DIRETO XR is awaiting connection.
- On = DIRETO XR is transmitting data via the Bluetooth
Smart protocol.
Green = DIRETO XR is connected via the ANT+ protocol.
- Blinking = DIRETO XR is awaiting connection.
- On = DIRETO XR is transmitting data via the ANT+
protocol.

09_POWER SENSOR CALIBRATION

DIRETO XR can calibrate the internal power measurement
system, which clears the system settings in order to always
obtain accurate power values.
The process is very simple, just select any type of training
on the home trainer and train for at least 5 minutes, then
perform the appropriate function - works on both the My
E-Training software and the My E-Training app.
The calibration command in the mobile version can be
found in Parameters – Advanced Configuration – Home
trainer calibration, while in the desktop version it can be
found in Settings – Home trainer calibration.
This is accomplished by pedalling and increasing speed
until you reach a certain indicated value.
Remember to stop pedalling at the system prompt.
After a few seconds the system will indicate that the
calibration process was successful.
This value is then stored in the DIRETO XR's memory, and
accurate power data will be received from every connected
device, including non-Elite third party software / app /
devices.
Please note: the aforementioned calibration procedure can
be conducted with software / app / devices other than the
Elite ones.

10_CADENCE SENSOR

The DIRETO XR uses an innovative "sensorless" system and
it's obtained via sophisticated power-based calculations.
When maintaining a high pedal cadence at low resistance
levels, there may occasionally be a slight inaccuracy in the
cadence value since it is the result of calculation and not
direct monitoring. This occurs especially with fast pedalling
and low resistance.
Should you wish for more accuracy than what the
"sensorless" system can give you, you can use a wired
sensor (not included) available for purchase via shop-Elite
or authorized retailers.
For installation on the bike, follow the instructions on the
enclosed manual.
To activate the cadence detection via the sensor, connect
the sensor to the DIRETO XR
Some software allows the use of wireless sensors
connected directly to the app/software/device. In this case,
please consult the specifications of the software / app /
device to verify its compatibility with wireless cadence
sensors.

11_HEART RATE MONITOR

- DIRETO XR hometrainer does not read heart rate monitor
data. Heart rate monitor data can be read directly from a
device that includes a heart rate function.
- Compatibility with various types of heart rate monitors
depends on the device / software / app being used only
ANT+ and is also compatible with Bluetooth Smart monitors
EN
33