General Specifications - Yamaha IPA 8200 Manual De Instrucciones

Specifications
General Specifications
Output Power
1kHz, THD+N=1%
20Hz-20kHz, THD+N=1%
1kHz, 20ms Burst
Maximum Input Level
Input Impedance
Input Sensitivity (dBu)
8Ω, Att. max
Voltage Gain
Att. Max
S/N Ratio
THD+N
Frequency Response
Channel Separation
Controls
Connectors
Indicators
Load Protection
Amplifier Protection
Power Supply Protection
Limiter Circuit
Cooling
AC Power Requirement
Power Consumption
Dimensions (W x H x D)
Weight
Included Accessories
• Half power = 3dB below rated power
• 0dBu = 0.775Vrms
• Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify
products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please
check with your Yamaha dealer.
Before you measure the output, refer to the cautions on the following page:
English: p.8 / German: p.17 / French: p.26 / Spanish: p.35 / Italian: p.44 / Russian: p.53
4Ω per channel
8Ω per channel
8Ω / BRIDGE
4Ω per channel
8Ω per channel
8Ω / BRIDGE
4Ω per channel
8Ω per channel
8Ω / BRIDGE
Switch Position
Input sensitivity
Switch Position
Voltage Gain
A-weighted
1kHz, half power, 4Ω
1W, 8Ω
1kHz, half power, 8Ω
Att. max, input 600Ω shunt
Front Panel
Rear Panel
Input
Output
Power
POWER switch on/off
DC-fault
Thermal
Over current
Thermal
Clip limiting
200W x 8
100W x 8
400W x 4
180W x 8
90W x 8
360W x 4
200W x 8
100W x 8
400W x 4
+24dBu
20kΩ(balanced), 10kΩ(unbalanced)
+4dBu 26dB
+4dBu +5.2dBu
+4dBu 26dB
27.2dB 26dB
≥100dB
≤0.5%
20Hz-20kHz, +0dB, –1.5dB
≥60dB
POWER switch (rocker)
MUTE switch (push ON/push OFF) x 8
Attenuator (41positon) x 8
MODE switch (STEREO/BRIDGE/PARALLEL) x 4
GAIN switch (+4dBu/26dB/32dB) x 1
HPF switch (OFF/20Hz/55Hz) x 1
Euroblock (balanced)/ch
Barrier strip/ch
AC inlet x 1
POWER x 1 (Green), PROTECT x 8 (Red),
CLIP x 8 (Red), SIGNAL x 8 (Green), MUTE x 8 (Red),
PARALLEL x 4 (Orange), BRIDGE x 4 (Orange)
Output mute
Power supply shutdown
Output mute (heatsink temp ≥95˚C)
Power supply shutdown
Power supply shutdown (heatsink temp ≥85˚C)
Limiting level ≥100W@8Ω or 200W@4Ω
High/Low two speed fan x 2
120V, 220V–240V; 50Hz/60Hz
400W
480 x 88 x 406.5 mm (18-7/8 x 3-7/16 x 16 inch)
(The depth is measured from the front panel surface to the
rear mounting hardware.)
10.5kg (23.2 lbs)
AC power cord (2.5m) x 1, Security cover x 1,
Allen wrench x 1, Security cover attachment screw x 2,
3-pin Euroblock connector x 8, Owner's manual
32dB
–0.8dBu
32dB
32dB
57
IPA8200 Owner's Manual