Wet Suction - Lavorwash COSTELLATION EGO 78 Manual Del Usuario

Inyección/extracción - aspiralíquido - aspiradora
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 17
vacuum operation is interrupted. Then switch off the
machine, disconnect the plug and empty the tank.
Regularly clean the water level limiting device (float)
and examine it for signs of damage.
If the machine overturns, it would be recommended
to release the trigger gun and then stud up the
machine.
If foam or liquid escape from the appliance, switch off
immediately.
The equipment should not be used to pick up
water from containers lavatories, tubs, etc.
Aggressive solvents or detergents should not be
used.
Service and repairs must be carried out by qualified
personnel only. Only use manufacturer original spare
parts for service repair.
The manufacturer cannot be held responsible for any
damage/injury caused to persons, animals or property
caused by misuse of the appliance, not in compliance
with manual instructions.
42 The machine must be always used on horizon-
tal bases.
43 Keep the machine on plane surfaces.
44 Do not use the machine without proper fil-
ters.
Before removing the motor unit A from the fil-
ter canister I, remove the hoses (T
release the latches G.
Do not pull on the water hoses that lead from
the motor unit A to the tank T.
USAGE
(see fig. ②③④)
DRY SUCTION
• Insert the filter E in the tank I.
• Hook up the motor head A on the tank I and lock
it up with the two hooks G.
• Fix the flexible hose L into the suction inlet H.
• Insert the extensions M into the end of the flex-
ible hose L and connect the most suitable acces-
sory.
• Plug the unit in.
• Turn on the illuminated ON-OFF switch C.
• Start the suction and choose 1 or 2 motors by
pressing the switches B.

WET SUCTION

• Remove the filter E from the tank I.
• Hook up the motor head A on the tank I and lock
it up with the two hooks G.
• Fix the flexible hose L into the suction inlet H.
• Fix, at the end of the flexible hose L, the exten-
sions M.
• Connect the accessories (O and O
• Plug the unit in.
• Turn on the illuminated ON-OFF switch C.
• Start the suction with 1 or 2 motors by pressing
the switch B.
INJECTION-EXTRACTION WASHING SYSTEM
• Preparation:
- Remove the filter E from the tank I.
- Pour detergent into the tank T
- Hook up the motor head A on the tank I and
- Insert the water hoses (T
- Fix the flexible hose L into the suction inlet H.
- Attach the end of the water hose U to the
- Fix, at the end of the flexible hose L, the exten-
and T
) and
1
2
- Secure the hoses (U
- Fix in the most suitable accessor.
• Operation:
- Plug the unit in.
- Turn on the illuminated ON-OFF switch C.
- Press the lever on the tap and both the switch-
- Release the lever on the tap (the pumps will
- Use the switches F.
- Use the switches B to turn on the 1 or 2
- To start cleaning, place the accessory on the
- When you've finished, turn off the switches F
- Use the lever on the tap to drain the residual
lock it up with the two hooks G.
T
quick-release connector located on the motor
unit A .
sions M.
provided.
es F to select operation of 1 or 2 motors.
automatically shut down).
pumps.
surface, press the lever on the tap, and pull it
toward you.
and B and the master switch C.
detergent.
If the detergent runs out, turn off the
switches F immediately to prevent damage to
the pumps.
9
).
1
.
1
and T
) into the tank
1
2
and U
) with the clips
1
2

Publicidad

Tabla de contenido
loading

Tabla de contenido