Speaker Placement - Mirage NANOSAT Manual Del Propietário

5. Mirage suggests setting the bass management crossover of your A/V Receiver or processor
to 120Hz. (Or as close to 120Hz as possible). If your A/V Receiver or processor does not
have a variable crossover, please proceed to the next step.
6. Balance the sound output of the speakers by using the pink noise test pattern generated
by your A/V Receiver or processor, adjusting the system so all speakers produce the same
output level.
7. When setting your subwoofer level, be sure that the setting on your A/V Receiver or
processor remains as close to flat as possible. Boosting or cutting the subwoofer output on
your A/V Receiver or processor may produce poor sound quality. Instead, use volume
control on the back of the NANOSUB for fine tuning.
You are now ready to enjoy your Mirage NANOSAT System.
IN-DEPTH INSTRUCTIONS
Stand Mount Options
This series provides a large choice of installation options to integrate into any decor.
The bottom of the NANOSAT is designed to clip onto the optional MS-STB-1 stand. Please refer
to the MS-STB-1 owners' manual for more detailed instructions.
Wall Mount Options
For wall mount installations, the NANOSAT is equipped with a mounting bracket that can be
used to mount the speaker securely to a vertical surface. The bracket is shipped already
attached to the speaker.
Carefully drive a #8 screw into a stud in the wall, leaving approximately 1/4 inch of the screw
exposed, then mount the NANOSAT like you would a picture. Note: Failure to attach the screw
safely to a secure spot on the wall can result is damage or injury. See Diagram 2
When mounting the speaker at a height of under six feet, orient the NANOSAT in an upright
position. Slide the head of the screw into the wide portion of the channel opening and slide
the NANOSAT downward until it sits in position. See Diagrams 2, 3
When mounting the speaker at a height of over six feet, orient the NANOSAT in an upside
down position so the grill is facing the floor and use the bottom key-way channel. Slide the
head of the screw into the wide portion of the channel opening and slide the NANOSAT
downward until it sits in position. See Diagrams 2, 3
The speaker can also be angled by slightly loosening the screw on the bottom of the NANOSAT
and swiveling the speaker into the desired position.

SPEAKER PLACEMENT

The MIRAGE ® NANOSAT System has been designed for high performance in a wide variety of
settings, but here are a few helpful hints that will help to maximize performance and your
enjoyment.
Left and Right Channels
A general guideline for speaker placement is to set up the space between speaker and listener
at approximately 1.5 times the distance between the speakers. For example, if the speakers
were ideally placed a minimum of 6 feet apart, the best seating position would be 9 feet away.
Ideal height would position the speaker at approximately ear level when the listener is in a
seated position. This can be accomplished by using the recommended optional MS-STB-1 stand.
Center Channel
A center channel can be expected to reproduce as much as 60% of a movie's soundtrack, most
of which is dialogue. In order to maintain the effect of voices emanating from the actor's
mouth, the NANOSAT being used as the center channel should be centrally located between
the left and right NANOSAT and be placed above or below the television.
Surround Channel
When using the NANOSAT as a surround speaker it should be positioned adjacent to and
slightly in front or behind the primary listening area. A general guideline for the recommended
height would be approximately 6 feet.
Bookshelf/Entertainment Unit Placement
The small size and OMNIPOLAR ™ dispersion of the versatile NANOSAT permits them to be easily
placed, among other places, in a bookshelf. If this is your preferred placement, affix the
isolating pads provided to the bottom of the speaker to help isolate the speaker from the shelf
and eliminate any transference of resonance. To maximize the OMNIPOLAR
potential, bring the speaker as close to the front of the cabinet as possible.
CONNECTIONS
The Mirage ® NANOSAT System is equipped with high quality binding posts that permit the use
of banana plugs, spades, or a bare wire connection.
Connect the speaker wire from the positive (RED +) terminal on the amp to the positive (RED+)
terminal on the speaker. Connect the negative (BLACK-) terminal on the amplifier to the
negative (BLACK-) terminal on the speaker. See Diagram 1
NANOSUB
Placement
Start off by placing the subwoofer near a corner in the front of the room. This will produce
maximum bass output. By moving the subwoofer away from the corner you will eventually find
the position that yields maximum bass output without "boominess". Note: it is important to
leave approximately 4 inches (10cm) of clearance between the subwoofer and walls or room
furnishings.
Connections
1. If you are using a digital receiver, connect the subwoofer from the receiver subwoofer pre-
amplifier output to the subwoofer RCA input, with a male to male RCA cable.
2. If your receiver does not have an RCA output, connect the speaker wire from the front left
and right outputs to the corresponding left and right inputs on the subwoofer, paying
particular attention to make sure that the polarities are maintained. Ensure Red (+) to Red
and Black (-) to Black connections are maintained.
Power Mode
The NANOSUB is equipped with a master power switch which must be engaged prior to use. If
the subwoofer will not be in use for extended periods of time, simply select the master power
switch "off" position. Next select the position of the Power Mode switch that is located on the
back panel of the subwoofer. There are 3 possible modes that the subwoofer can be operated in:
1. OFF- Turns Subwoofer Power OFF. The Subwoofer will not operate in this mode. Use this
mode if the Subwoofer is inactive for short periods of time. If the subwoofer will not be in
use for extended periods of time, unplug the AC cord from the wall receptacle.
2. Auto- In this mode the Subwoofer turns ON in the presence of an audio signal then turns
OFF with a delay when the audio signal disappears. The indicator light on the front of the
subwoofer will specify whether the subwoofer is in standby mode (Glows Red) or in
Operational mode (Glows Green). This is the recommended mode for general operation.
3. ON- the Subwoofer remains in the operational mode and will not shut off when the audio
signal disappears. This position is useful when watching television or satellite TV where
low frequency information is not as robust as CD's or DVD's. The Indicator light will
permanently glow green in this mode.
WARRANTY OUTSIDE OF
THE UNITED STATES
Outside of North America, the warranty may be changed to comply with local regulations. Ask
your local MIRAGE
WARRANTY FOR THE UNITED STATES
AND CANADA
Please see the warranty document on the back cover
"MIRAGE", the "MIRAGE" logo, are trademarks of Audio Products International Corp.
™ dispersion
3
® dealer for details of the LIMITED WARRANTY applicable in your country.