König KN-URC20B Manual De Instrucciones página 12

All manuals and user guides at all-guides.com
Manual TV set programming
1) Switch your TV set on.
2) Look up the brand of your TV set under "TV" in the code list. Single or multiple 4 digit codes are shown for
each brand.
3) Press and hold the TV Standby button (
4) Use the number keys to enter the fi rst four-digit code from the code list for the brand that you have selected.
The signal LED ( ) fl ashes twice to indicate that the code has been accepted.
5) Test the functionality of your remote control using the TV standby button (
6) If the TV set does not respond, or only responds partially to the commands, repeat steps 3 to 5 using the next
code from the code list.
7) If the TV set responds properly to all functions, your KN-URC20B is correctly programmed and can be used.
Please note the code that was used for future reference.
Manual programming for the satellite receiver and the DVB-T (Freeview)/cable-box
(STB)
1) Switch your satellite receiver or DVB-T (Freeview)/cable-box (STB) and TV set on.
2) Look up the brand of your unit under "STB" in the code list. Single or multiple 4 digit codes are shown for each
brand.
3) Press and hold the STB Standby button (
4) Use the number keys to enter the fi rst 4-digit code from the code list for the brand that you have selected. The
signal LED ( ) fl ashes twice to indicate that the code has been accepted.
5) Now test the individual buttons on your remote control for function, starting with the STB Standby button
( ), volume buttons (
stb vol
description table). The AV button (
6) If the unit does not respond, or only responds partially to the commands, repeat steps 3 to 5 using the next
code from the code list.
7) If the unit responds properly to all functions, your KN-URC20B is correctly programmed and can be used.
Please note the code that was used for future reference.
My programming codes to use
TV STB
Automatic programming the TV set according to brand
As an alternative, and if the correct code for your TV set cannot be found for manual programming, you can use
the automatic search function by brand for programming.
1) Switch your TV set on.
2) Look up the brand of your TV set in the brand list in the appendix to this instruction manual. There is a 3-digit
brand code for each brand.
3) Press and hold the TV Standby button (
4) Use the number buttons to enter the code 1 0 0 3. The Signal LED (
search mode has been activated.
5) Use the number keys to enter the three-digit brand code from the brand list for the brand that you have
selected. The signal LED (
6) Hold down the TV Standby button (
take several minutes.
7) As soon as the unit has switched off, push the OK button to confi rm the programming (
LED ( ) fl ashes twice.
8) Test the functionality of your remote control using the TV standby button (
TV set responds properly to all functions, your KN-URC20B is correctly programmed and can be used.
BA König KN-URC20B, 135x215 mm CS6.indd 12 BA König KN-URC20B, 135x215 mm CS6.indd 12
) until the signal LED (
tv
) until the signal LED (
stb
/ ), and then with the buttons 1 to 43 (in accordance with functional
vol
) and TV Standby button (
av
) until the signal LED (
tv
) fl ashes twice to indicate that the code has been accepted.
) on your KN-URC20B until the TV set switches off. This process can
tv
12
) fl ashes twice.
) and the AV button (
tv
) fl ashes twice.
) are not tested.
tv
) fl ashes twice.
) fl ashes twice to confi rm that the
) until the Signal
ok
) and the AV button (
tv
12.09.2012 09:32:11 12.09.2012 09:32:11
).
av
). If the
av