Learn Feature - König KN-URC20B Manual De Instrucciones

All manuals and user guides at all-guides.com
1) Switch your TV set, satellite receiver or DVB-T (Freeview)/cable-box (STB) on.
2) Press and hold the STB Standby button (
3) Use the number buttons to enter the code 3 0 0 1. The Signal LED (
search process has been activated.
4) Hold down the STB Standby button (
take several minutes.
5) As soon as the unit has switched off, push the OK button to confi rm the programming (
LED ( ) fl ashes twice.
6) Now test the individual buttons on your remote control for function, starting with the STB Standby button
( ), volume buttons (
stb vol
description table). The AV button (
7) If the unit responds properly to all functions, your KN-URC20B is correctly programmed and can be used.
Note :
It could happen, that during the search process, the KN-URC20B fi nds several codes to which your unit responds,
but where all buttons do not function for each code. In this case, the search process should be re-started (steps 2
to 7) until you obtain the best code. Re-starting the search process starts at the last saved programming.
Code reader
The code reader can be used to display the codes that you have found in the search process so that you can
make a note of them:
1) Press and hold the TV Standby button (
fl ashes twice.
2) Use the number buttons to enter the code 0 0 0 2. The Signal LED (
3) Push 1 and count the number of times the Signal LED fl ashes; this is the fi rst number.
4) Push 2 and count the number of times the Signal LED fl ashes; this is the second number.
5) Push 3 and count the number of times the Signal LED fl ashes; this is the third number.
6) Push 4 and count the number of times the Signal LED fl ashes; this is the fourth number.
Note :
The Signal LED does not fl ash if the number is 0. The steps 3 to 6 can be carried out in any order and as many
times as may be required.

Learn feature

Alternatively, or if either in case of manual programming or with automatic programming, the correct code for your
equipment cannot be found, you may use the learn feature.
The learn feature may also be used if certain button functions of the original remote control are not included in the
database.
Positioning the KN-URC20B and original remote control (Range test)
In order to ensure that the remote control can receive the signal, both remote controls should be placed opposite
one another with their transmission diodes facing each other. The distance between both remote controls should
not be greater than 5 cm.
You may use the range test to determine the optimal position for learning the codes:
1) Press and hold the TV Standby button (
fl ashes twice.
2) Enter the code 0 0 1 1 using the numeric buttons. The signal LED fl ashes twice again.
3) Now, the signal LED lights up in orange and displays the quality of the signals received.
Now place the original remote control and press and hold any button on it.
Change the distance to the KN-URC20B remote control until the signal LED lights up in green.
Note :
Orange light indicates readiness and that the KN-URC20B is not receiving any signal.
If the signal LED lights up in red, it means that the signal is too weak (too far away) or too strong (too near).
If the signal LED lights up in green, it indicates optimal signal quality (optimal alignment for learning).
4) To end the range test, press the TV Standby button (
pressed earlier.
BA König KN-URC20B, 135x215 mm CS6.indd 14 BA König KN-URC20B, 135x215 mm CS6.indd 14
) until the signal LED (
stb
) on your KN-URC20B until the unit switches off. This process can
stb
/ ), and then with the buttons 1 to 43 (in accordance with functional
vol
) and TV Standby button (
av
) or the STB Standby button (
tv
) or the STB Standby button (
tv
) or STB Standby button (
tv
14
) fl ashes twice.
) fl ashes twice to confi rm that the
) until the Signal
ok
) are not tested.
tv
) until the LED Signal (
stb
) fl ashes twice again.
) until the LED Signal (
stb
) that had been
stb
12.09.2012 09:32:19 12.09.2012 09:32:19
)
)