Makita 6991D Manual De Instrucciones página 5

ENGLISH
1 Push button
2 Battery cartridge
3 Charging light
4 Fast charger
5 Socket
6 Anvil
7 Pin
8 O-ring
SPECIFICATIONS
Model
Capacities
Standard bolt .......................................................... M8 — M14
High tensile bolt ...................................................... M6 — M10
Square drive .............................................................. 9.5 mm
–1
No load speed (min ) ............................................... 0 — 2,300
Impacts per minute .................................................... 0 — 3,000
Max. fastening torque ................................................ 100 N . m
Overall length ............................................................ 168 mm
Net weight (with battery cartridge) ............................ 1.3 kg
Rated voltage ............................................................ D.C. 9.6 V
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Safety Hints
For your own safety, please refer to the enclosed
safety instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating
instructions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
3. CAUTION — To reduce risk of injury, charge
only MAKITA type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or
sold by the battery charger manufacturer may
result in a risk of fire, electric shock, or injury
to persons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when dis-
connecting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise sub-
jected to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
All manuals and user guides at all-guides.com
Explanation of general view
9 Switch trigger
10 Reversing switch lever
11 A side
12 B side
13 Clockwise
14 Counterclockwise
15 Fastening time
16 Seconds
6991D
ENC001-2
17 Proper fastening torque for
18 Fastening torque
19 Screw
20 Set plate
21 Limit mark
22 Screwdriver
23 Brush holder cap
9. Do not operate charger if it has received a
sharp blow, been dropped, or otherwise dam-
aged in any way; take it to a qualified service-
man.
10. Do not disassemble charger or battery car-
tridge; take it to a qualified serviceman when
service or repair is required. Incorrect reas-
sembly may result in a risk of electric shock or
fire.
11. To reduce risk of electric shock, unplug
charger from outlet before attempting any
maintenance or cleaning. Turning off controls
will not reduce this risk.
12. The battery charger is not intended for use by
young children or infirm persons without
supervision.
13. Young children should be supervised to
ensure that they do not play with the battery
charger.
ADDITIONAL SAFETY RULES FOR
CHARGER & BATTERY CARTRIDGE
1. Do not charge battery cartridge when tempera-
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
2. Do not attempt to use a step-up transformer,
an engine generator or DC power receptacle.
3. Do not allow anything to cover or clog the
charger vents.
4. Always cover the battery terminals with the
battery cover when the battery cartridge is not
used.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
6992D
M8 — M14
M6 — M10
12.7 mm
0 — 2,300
0 — 3,000
100 N . m
176 mm
1.4 kg
D.C. 9.6 V
5