Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
5. SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool
is maintained.
ELECTRICAL SAFETY
This product must be earthed. Always check
that the power supply corresponds to the
voltage on the rating plate.
VOLTAGE DROPS
Inrush currents cause short-time voltage drops.
Under unfavourable power supply conditions, other
equipment may be affected. For example, artificial
lighting will show a temporary drop in magnitude when
the machine is switched on.
If the system impedance of the power supply is lower
than 0.19 ø , disturbances are unlikely to occur.
This appliance is not intended for use by young or
infirm persons without supervision. Children must
be supervised to ensure they do not play with the
appliance.
If the supply cord is damaged, it must be replaced
by the manufacturer or an authorised Stayer Service
Centre in order to avoid a hazard.
ADDITIONAL SAFETY INSTRUCTIONS FOR
HEATGUNS
Warning! This tool is not intended for use by young or
infirm persons. Children must be supervised to ensure
they do not touch the tool.
Warning! Always place the tool in the stand position
when not in use.
A fire may result if the tool is not operated carefully,
therefore always use the tool with care and attention.
Do not obstruct either the air intake slots or the nozzle
outlet as this may cause excessive heat build up
resulting in damage to the tool.
Be careful when using the appliance in places where
there are combustable materials.
Do not direct the hot air flow at other people or animals.
Do not touch the nozzle as it becomes very hot during
use and remains hot for up to 30 minutes after use.
Do not place the nozzle against any object during or
immediately after use.
Do not poke anything down the nozzle as it could give
you an electric shock.
Do not look down the nozzle while the tool is switched
on.
Do not use the tool as a hairdryer! The air temperature
is far higher than a hairdryer.
Ensure adequate ventilation during use as toxic fumes
may be produced.
Do not use the tool in a damp atmosphere.
Be aware that heat may be conducted to combustible
materials that are out of sight. Spaces behind boards,
ceilings and floors and wall cavities in timber frame
constructed houses can contain flammable materials.
Check before starting work.
Do not use in presence of an explosive atmosphere;
i.e.
Do not use the tool where flammable gases, liquids or
materials may be present.
When stripping paint, ensure that the work area is
enclosed. Wear a dust mask specifically designed
for protection against lead paint dust and fumes and
ensure that persons within or entering the work area
are also protected.
Do not burn paint. as it could cause a fire hazard.
Do not allow paint to adhere to the nozzle as it could
ignite after some time.
Do not apply heat to the same place for a long time
Do not leave the appliance unattended when it is
switched on or when cooling down.
Switch off he tool and allow it to cool before fitting any
accessory.
Allow the tool to cool down fully before storing.
Stripping lead-based paint
Extreme care should be taken when stripping paint.
The peelings, residue and vapours of paint may contain
lead, which is poisonous. Any pre-1960 building may
in the past have been painted with paint containing
lead. This paint may becovered with additional layers
of paint. Once deposited on surfaces, hand to mouth
contact can result in the ingestion of lead.
Exposures to even low levels of lead can cause
irreversible brain and nervous system damage. The
greatest danger of lead poisoning is to children and
pregnant women.
Before starting work, it is important to determine
whether the paint to be stripped contains lead. This can
be done using a test kit or by a professional decorator.
Do not smoke, eat or drink in a work area that could
or may be contaminated by lead. Lead based paints
should only be removed by a professional and should
not be removed using a heatgun.
ILLUSTRATED DESCRIPTION
1. ON/OFF Switch power switch
2. Heat control knob
3. Nozzle
4. Ventilation
5. Temperature adjustment knob (SU650EDK)
6. Digital LCD Display (SU650EDK)
7. Temperature decrease button (SU650EDK)
-
17
-
es
it
gb
de
fr
p
pl
el
Publicidad
Tabla de contenido
