Analog Output Jack Section; Screen Operation Section - Tascam 16 Manual Del Usuario

Analog output jack section

MAIN OUTPUT L/R jacks
h
These analog outputs are XLR jacks.
o XLR (1: GND, 2: HOT, 3: COLD)
j FOOTSWITCH jack
This standard TS jack is for connecting a footswitch.
o TS (Tip: HOT, Sleeve: GND)
NOTE
This unit was designed to be used with unlatched
(momentary) footswitches that have to be pushed to
function (shorted when pushed).
SUB OUTPUT L/R jacks
k
These standard TRS jacks are analog outputs.
o TRS (Tip: HOT, Ring: COLD, Sleeve: GND)
l MASTER SECTION EQ knobs
This 4-band semi-parametric
from the MAIN OUTPUT and AUX OUTPUT MON 1/2 jacks.
AUX OUTPUT MON 1/2 jacks
;
These standard TRS jacks are analog outputs.
o TRS (Tip: HOT, Ring: COLD, Sleeve: GND)

Screen operation section

Display
,
Shows a variety of information.
USB indicator
.
This lights when the USB connection is working.
equalizer affects signals output
2 - Names and Functions of Parts
AUX OUTPUT FX jack
z
This standard TRS jack is an analog output.
When an external effect is connected, signals will not be sent
to the built-in effect.
When using an external effect, turn the built-in effect off.
o TRS (Tip: HOT, Ring: COLD, Sleeve: GND)
CONTROL ROOM L/R jacks
x
These standard TRS jacks are analog outputs.
Use these to monitor signals from the MAIN MIX L/R bus or
PFL/AFL L/R bus. (See "Block diagram" on page 63)
o TRS (Tip: HOT, Ring: COLD, Sleeve: GND)
PHONES jack
c
Use this standard stereo jack to connect stereo headphones.
Use an adapter to connect headphones with a mini plug.
Use this to monitor signals from the MAIN MIX L/R bus or
PFL/AFL L/R bus. (See "Block diagram" on page 63)
PHANTOM +48V switch and indicator
v
Use this switch to supply +48V phantom power to the 1-2,
3-8 and 9/10-11/12
The indicator lights when the PHANTOM +48V switch is set
to on (pushed in). (See "Setting phantom power" on page
36)
SD card slot
b
Insert SD cards in this slot. (See "Inserting and removing SD
cards" on page 31)
MON 1/2/MAIN MIX switch
n
Set which output signals are affected by the equalizer.
MAIN MIX: Equalizer is applied to signals sent from the
MAIN MIX L/R bus.
MON 1/2: Equalizer is applied to signals sent from the
MONITOR OUT 1/2 buses.
NOTE
Also set the EQ IN/BYPASS switch to EQ IN.
EQ IN/BYPASS switch
m
When this switch is EQ IN, the equalizer will affect the output
signals set with the MON 1/2/MAIN MIX switch.
When set to BYPASS, the equalizer will not be applied
regardless of the MON 1/2/MAIN MIX switch setting.
PFL/AFL indicator
/
This indicator lights when at least one channel PFL switch is
on or when the AFL switch for the MON 1 or MON 2 knob or
the FX fader is on.
Function buttons
!
The functions of these buttons change depending on the
screen shown on the display. The functions shown at the
bottom of the display are the currently assigned functions.
NOTE
For convenience, the four buttons under the display are
called the function buttons in this manual. From left to right,
they are called the F1, F2, F3 and F4 buttons.
MIC input jacks on the top of the unit.
TASCAM Model 16
23