Stanley SP137 Manual De Instrucciones página 20

b. Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c. Do not position your body in the area where
power tool will move if kickback occurs. Kickback
will propel the tool in direction opposite to the wheel's
movement at the point of snagging.
d. Use special care when working corners, sharp
edges, etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing have a
tendency to snag the rotating accessory and cause loss
of control or kickback.
e. Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create frequent
kickback and loss of control.
ADDITIONAL SAFETY INSTRUCTIONS FOR
POLISHING OPERATIONS
Safety Warnings Specific for Polishing Operations
a. Do not allow any loose portion of the polishing
bonnet or its attachment strings to spin freely.
Tuck away or trim any loose attachment strings.
Loose and spinning attachment strings can entangle
your fingers or snag on the workpiece.
b. When adding lubricating oil and changing
accessories please follow this manual instruction.
c. The handle must keep dry clean and without oil.
ADDITIONAL SPECIFIC SAFETY RULES
WARNING! Safety Instructions for Polisher
a. Always use eye protection. All users and bystanders
must wear eye protection that conforms to ANSI Z87.1.
b. Clean out your tool often, especially after heavy
use. Dust and grit containing metal particles often
accumulate on interior surfaces and could create an
electric shock hazard.
c. Do not operate this tool for long periods of time.
Vibration caused by the operating action of this tool may
cause permanent injury to fingers, hands and arms.
Use gloves to provide extra cushion, take frequent rest
periods and limit daily time of use.
d. Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be
caught in moving parts.
e. Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be
caught in moving parts.
WARNING: ALWAYS use safety glasses.Everyday
eyeglasses are NOT safety glasses.Also use face
or dust if cutting operation is dusty.ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT.
WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19)
during use. Under some conditions and duration of
use, noise from this product may contribute to hearing loss.
WARNING: Use of this tool can generate and/or
disperse dust, which may cause serious and
permanent respiratory or other injury. Always use
20
NIOSH/OSHA approved respiratory protection appropriate for
the dust exposure.Direct particles away from face and body.
CAUTION: Use extra care when working into a
corner because a sudden, sharp movement of the
polisher may be experienced when the wheel or other
accessory contacts a secondary surface or a surface edge.
Additional Safety Information
WARNING: We recommend the use of a residual
current device with a residual current rating of
30mA or less.
RESIDUAL RISKS
Additional residual risks may arise when using the tool
which may not be included in the enclosed safety warnings.
These risks can arise from misuse, prolonged use etc. In
spite of the application of the relevant safety regulations and
the implementation of safety devices, certain risks cannot
be avoided. These are:
♦ Injuries caused by touching any rotating/moving parts.
♦ Injuries caused when changing any parts, blades or
accessories.
♦ Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
♦ Impairment of hearing.
♦ Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
SAFETY OF OTHERS
♦ This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
♦ Children should be supervised to ensure that they do
not play with the appliance.
LABELS ON TOOL
The following symbols are shown on the tool along with date
code:
WARNING! To reduce the risk of injury, the user
must read the instruction manual before use.
Wear ear protection.
Wear safety glasses or goggles.
Wear a dust mask.
V Volts
A Amperes
Hz Hertz
Direct Current
n No-Load Speed
0
Class II Construction