Safety Precautions - Bixolon SRP-380 Guia De Instalacion

◈ Self-Test
1. Check whether paper is mounted correctly.
2. Turn on the power while holding down the Feed button and the self-test procedure will begin.
3. Printer will print out the current status of printer including the version of ROM and DIP switch
settings.
4. After printing out the current status of printer, the printer will print following lines and waits for
the next step(paper lamp will keep blinking).
SELF-TEST PRINTING.
PLEASE PRESS THE FEED BUTTON.
Continuous SELF-TEST : Less than 1 second
VMSM Selection : 1second or more
5. Press the Feed button to resume printing or hold down the button for at least one second to
change the VMSM settings.
5-1 If "Continuous SELF-TEST" is selected
5-1-1 Press the Feed button for less than one second to print the preset page.
5-1-2 The self test ends automatically as it prints the following line and cuts the paper.
*** COMPLETED ***
5-1-3 The printer goes into normal print mode upon completion of the self test.
5-2 If "VMSM Selection" is selected
5-2-1 The following lines will be printed when the VMSM opens.
** VMSM Selection **
0: Exit and reboot printer / 1: Print current settings / 2: Set Print Density
3: Set Print Speed / 4: Set Cutting mode / 5: Set External Buzzer after cutting
6: Set Internal Buzzer after cutting / 7 or more: None
5-2-2 Press the Feed button to run the above function.
5-2-2-1 Step 1(Select Options): press the button a number of times as shown by each menu.
5-2-2-2 Step 2(Enter Options): hold down the button for at least one second to apply each item
selected.
※ Note
If you select any items not listed above, the list of "VMSM Selection" will be printed again. Setting the
mode will be canceled if no item is selected in Step 1.
5-3 Hold down the Feed button for at least 1 second to save the changes. The following line will be
printed before cutting the paper.
※ Attention
If "0: Exit and reboot printer" is not executed, the new settings will not be saved.
*** COMPLETED ***
6. The new settings will be automatically applied when printer resets.
※ Note
You can check whether printer works correctly or not through the self-test. Printing quality, ROM
version, and DIP switch settings can be checked through the self-test function.
◈ WEEE(Waste Electrical and Electric Equipment)
This marking shown on the product or its literature, indicates that is should not be disposed
of with other household wastes at the end of its working life. To prevent possible harm to
the environment or human health from uncontrolled waste disposal, please separate this
from other types of wastes and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer where they purchased
this product, or their local government office, for details of where and how they can take this
item for environmentally safe recycling. Business users should contact their supplier and
check the terms and conditions of the purchase contract. This product should not be mixed
with other commercial wastes for disposal.

◈ Safety Precautions

In using the present appliance, please keep the following safety regulations in
order to prevent any hazard or material damage.
WARNING
Violating following instructions can cause serious injury or death.
Do not plug several products in one
multi-outlet.
• This can provoke over-heating and a fire.
• If the plug is wet or dirty, dry or wipe it before
usage.
• If the plug does not fit perfectly with the outlet,
do not plug in.
• Be sure to use only standardized multi-outlets.
PROHIBITED
Do not pull the cable to unplug.
• This can damage the cable, which is the
origin of a fire or a breakdown of the printer.
PROHIBITED
Do not plug in or unplug with your hands
wet.
• You can be electrocuted.
PROHIBITED
CAUTION
Violating following instructions can cause slight wound or damage the
appliance.
If you observe a strange smoke, odor or noise
from the printer, unplug it before taking
following measures.
• Switch off the printer and unplug the set from the
mains.
• After the disappearance of the smoke, call your
dealer to repair it.
TO UNPLUG
PRINTER
Install the printer on the stable surface.
• If the printer falls down, it can be
broken and you can hurt yourself.
PRINTER
PROHIBITED
Do not let water or other foreign objects
in the printer.
• If this happened, switch off and unplug
the printer before calling your dealer.
PROHIBITED
PRINTER
You must use only the supplied adapter.
• It is dangerous to use other adapters.
ONLY SUPPLIED ADAPTER
PROHIBITED
Keep the plastic bag out of children's
reach.
• If not, a child may put the bag on his head.
PROHIBITED
Do not bend the cable by force or leave it
under any heavy object.
• A damaged cable can cause a fire.
PROHIBITED
Keep the desiccant out of children's reach.
• If not, they may eat it.
PROHIBITED
Use only approved accessories and do not
try to disassemble, repair or remodel it for
yourself.
• Call your dealer when you need these services.
• Do not touch the blade of auto cutter.
DISASSEMBLING
PROHIBITED
PRINTER
Do not use the printer when it is out
of order. This can cause a fire or an
electrocution.
• Switch off and unplug the printer
before calling your dealer.
TO UNPLUG
PRINTER
DEALER