ETI Solid State Lighting MBOV-8.5IN-8-3CP-MV-WT Manual De Uso Y Cuidado

8.5" OVAL TWISTFIT MARINE BULKHEAD WITH COLOR PREFERENCE
PACKAGE CONTENTS
Part Description
A Fixture Body
AA Mounting Bracket
BB Mounting Screw (for Bracket)
CC Wire Connector
NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: Shut off the power at the circuit breaker or fuse panel before removing the old fixture, ballast, or fluorescent tubes.
NOTE: Stick the replacement label on the inner wall of the recessed housing before installation.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
INSTALLATION 1
Remove the rubber plug and using a philips head screw driver access
1
the color temperature setting switch cover. Choose color temperature
(CCT) from three options: 2700k Warm White, 3000k Soft White, or
4000k Cool White. Install the color switch cover, then fix the screw
with a philips head screw driver and replace rubber plug.
NOTE: The factory
setting for the
correlated color
temperature (CCT)
is 2700K.
2700K 3000K 4000K
Align the side slots on the fixture
4
body (A) with the mounting bracket
(AA) and fix the fixture body (A)
securely by carefully rotating in
clockwise the side slots inside the
mounting bracket (AA).
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or
other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. • This
product must be installed in accordance with the applicable installation codes by a person familiar with the construction and operation of the product and the hazards involved. • Risk
of electrical shock. To reduce the possibility of serious injury, always take the proper precautions and unplug the fixture before moving or cleaning.
NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, and consult the dealer or an experienced radio/TV.
NOTICE: Suitable for operation in ambient temperatures not exceeding 113°F/45°C. • Suitable for wet locations.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
• Twist Fit products are not compatible with all the shallow pancake junction boxes.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
USE AND CARE GUIDE
Quantity
1
1
2
2
A
Switch cover
Rubber plug
HORIZONAL MOUNTING
Side slot
A
AA
VERTICAL MOUNTING
Side slot
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com
A AA
Pass the hot and neutral (black and white)
2
wires from the electrical outlet box through
the middle hole of the mounting bracket
(AA). Align the mounting bracket (AA) using
the mounting screws (BB) and tighten
securely to the electrical box.
AA
BB
Model # 504071020
Part # MBOV-8.5IN-8-3CP-MV-WT
®
BB CC
Connect the hot and neutral (black and
3
white) wires from the fixture body (A) to
the same color wires from the electrical
box. Cover the wire connectors (CC)
with electrical tape for a more secure
connection. Position the wires back inside
the electrical box.
CC
A
Silicone Sealant
Apply silicone sealant
5
(not included)
( not included) between
the fixture body (B) and
the wall for additonal
protection against water
and dust. Restore power at
the electrical panel. Turn on
the light switch to activate
the fixture.
AA