Publicidad
A. Construction and characteristics
Transportable terrace/garden heater with tank housing
A. Construction and characteristics
• Transportable terrace/garden heater with tank housing
Casing in steel with powder-coating or stainless steel
• Casing in steel with powder-coating or stainless steel
Heat emission from reflector
• Heat emission from reflector
B. Specifications
B. Specifications
• Use propane or butane gas only
Use propane or butane gas only
• Max. wattage: 13000 watts
• Min. wattage: 5000 watts
Max. wattage: 13000 watts
• With CE certificates
Min. wattage: 5000 watts
C. Table of injector
With CE certificates
MODEL
21012 FLAMEHEATER
C. Table of injector
GAS CATEGORY:
ASSEMBLY PARTS AND PROCEDURES
TYPES OF GAS:
Butane
GAS PRESSURE:
Tools needed:
28-30 mbar
TOTAL HEAT
Open end wrench 10 & 13 mm
13kW (870g/h)
INPUT
(Hs): (Qn)
Adjustable opening wrench (2) 20 cm long
1.90 mm for main burner
Slip joint pliers 23 cm long
INJECTOR SIZE:
0.18 mm for pilot burner
Philips screwdriver w/ medium blade
• The hose and regulator assembly must conform to local standard codes.
Spray bottle of soap solution for leakage test
• Regulator outlet pressure should meet the corresponding gas category in the table of injector.
• The appliance requires approved hose in 1.2m length.
The hose and regulator assembly must conform to local standard codes.
Regulator outlet pressure should meet the corresponding gas category in the table of injector.
ASSEMBLY PARTS AND PROCEDURES
The appliance requires approved hose in 1.2m length.
Parts supplied:
Tools needed:
• Open end wrench 10 & 13 mm
Stand with LPG cylinder housing and 3 post brackets.
• Adjustable opening wrench (2) 20 cm long
9 Cup Nuts (M6 mm),9 Small Screws (M6 x 8 mm) for Reflector Assembly.
• Slip joint pliers 23 cm long
• Philips screwdriver w/ medium blade
6 Large Bolts and Flange Nuts (M6) for Support Legs/Main Pole Assembly.
• Spray bottle of soap solution for leakage test
3 Medium Bolts (M8 x 16 mm) for Support Legs/Stand Assembly.
Parts supplied:
3 Reflector Spacers and Wing Nuts, 6 Large Flat Washers for Reflector and burner Assembly.
• Stand with LPG cylinder housing and 3 post brackets.
• 9 Cup Nuts (M6 mm),9 Small Screws (M6 x 8 mm) for Reflector Assembly.
2 Medium Bolts (M8x16 mm) for wheels and base.
• 6 Large Bolts and Flange Nuts (M6) for Support Legs/Main Pole Assembly.
6 Small bolts (M6x12) and M6 nuts for anchoring arm and base.
• 3 Medium Bolts (M8 x 16 mm) for Support Legs/Stand Assembly.
• 3 Reflector Spacers and Wing Nuts, 6 Large Flat Washers for Reflector and burner Assembly.
• 2 Medium Bolts (M8x16 mm) for wheels and base.
• 6 Small bolts (M6x12) and M6 nuts for anchoring arm and base.
ASSEMBLY PROCEDURES
ASSEMBLY PROCEDURES
Attach wheel assembly to base with 2pcs Medium bolts (M8x16mm)
Attach wheel assembly to base
with 2pcs Medium bolts (M8x16mm)
ASSEMBLY PARTS AND PROCEDU
Tools needed:
Open end wrench 10 & 13 mm
Adjustable opening wrench (2) 20 cm long
Slip joint pliers 23 cm long
Philips screwdriver w/ medium blade
Spray bottle of soap solution for leakage test
I
I
3+(28-30/37)
3B/P(30)
Propane
LPG Gas Mixtures
Parts supplied:
37 mbar
30 mbar
Stand with LPG cylinder housing and 3 post brackets.
9 Cup Nuts (M6 mm),9 Small Screws (M6 x 8 mm) for Reflector Assembly.
6 Large Bolts and Flange Nuts (M6) for Support Legs/Main Pole Assembly.
3 Medium Bolts (M8 x 16 mm) for Support Legs/Stand Assembly.
3 Reflector Spacers and Wing Nuts, 6 Large Flat Washers for Reflector and
2 Medium Bolts (M8x16 mm) for wheels and base.
6 Small bolts (M6x12) and M6 nuts for anchoring arm and base.
ASSEMBLY PROCEDURES
Attach wheel assembly to base with 2pcs Medium bolts (M8x16mm)
Attach 1 anchoring arm to base with 2 small bolts
Attach 1 anchoring arm to base with 2 small bolts M6x12mm and 2pcs M6 nuts
M6x12mm and 2pcs M6 nuts as shown
(repeat with the other 2anchoring arms so all 3 are attached to base).
(repeat with the other 2anchoring arms so all 3 are
attached to base).
- 5 -
2575-21
Pin: 2575DM30400
I
I
3B/P(37)
3B/P(50)
LPG
Gas Mixtures
LPG Gas Mixtures
37mbar
50mbar
1.90 mm for main burner
1.68 mm for main burner
0.18 mm for pilot burner
0.18 mm for pilot burner
37
Publicidad
Capítulos
