Publicidad
M.-Nr. 05719362
A
Place the supplied mat on the machine lid and align it with the edges of the machine lid with W = 2 3/8" (60.5 mm)
and Z = 1 1/4" (31 mm); see Fig. 2.
A
Drill holes with Ø 1/4" (6.5 mm); see Fig. 2.
A
Drill hole with Ø 1/8" (3 mm); see Fig. 2.
A
Drill hole with Ø 1 3/16" (30 mm); see Fig. 2.
A
Use the Ø 1 3/16" (30 mm) (10) hole for the connection cable with strain relief; see Fig. 4.
Drilling mounting holes
This part of the instructions only applies to the following models:
PT 7251, PT 7331, PT 8251, PT 8251 COP, PT 8253, PT 8255, PT 8331, PT 8331 COP, PT 8333, PT 8335, PT 8257,
PT 8337
A
Place the supplied rubber mat on the machine lid and line it up with the edges of the machine lid with
X = 2 3/8" (60.5 mm) and Y = 1 1/4" (31 mm); see Fig. 3.
A
Drill 4 holes with Ø 1/4" (6.5 mm); see Fig. 3.
A
Punch out the prepunched hole for feeding through the cable on the rear panel of the machine.
A
Use the prepunched hole for the connection cable (12) with strain relief (11); see 5.
Drilling mounting holes
This part of the instructions only applies to the following models:
PW 6107, PW 6137, PW 6167, PW 6207
A
Place the supplied rubber mat on the machine lid and line it up with the edges of the machine lid with X =
2 3/8" (60.5 mm) and Y = 1 1/4" (31 mm); see 2.
A
Drill 4 holes with Ø 1/4" (6.5 mm); see Fig. 2.
A
Punch out the prepunched hole (1) for feeding through the cable on the top rear panel of the machine; see Fig. 6.
A
Use the prepunched hole for the connection cable with strain relief.
Drilling mounting holes
This part of the instructions only applies to the following models:
PW 413, PW 418, PW 811, PW 814, PW 818
A
Place the supplied rubber mat on the machine lid and line it up with the edges of the machine lid with
X = 2 3/8" (60.5 mm) and Y = 1 1/4" (31 mm).
This serves as the drilling template; see Fig. 2.
A
Drill 4 holes with Ø 1/4" (6.5 mm); see Fig. 2.
A
Punch out the prepunched hole (1) for feeding through the cable on the top rear panel of the machine; see Fig. 7.
A
Use the prepunched hole for the connection cable with strain relief.
Drilling mounting holes when replacing the payment device
This part of the instructions applies when replacing a C 5002 or C 5003 payment device with a C 4060, C 4065, or
C 4070 payment device.
A
When replacing a C 5002, new holes must be drilled in the machine lid; see Fig. 8.
A
When replacing a C 5003, new holes must be drilled in the machine lid; see Fig. 9.
Drilling mounting holes
This part of the instructions only applies to the following models:
PWM, PDR generation
Diese Unterlagen dürfen ohne unsere Genehmigung weder vervielfältigt noch Dritten zugänglich gemacht werden. Eigentumsrechte vorbehalten.
Umbau- und Montageanweisung
30 von 63
20.01.2022
Publicidad
