Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATING INSTRUCTIONS
Pu ng into service
To use ORIGAMI, it is first necessary to connect the power
cord to the electrical socket using the plug supplied.
On doing this, the device emits two beeps las ng 0.5 seconds
and the LEDs at the base of the product will emit a WHITE
LIGHT. ORIGAMI is therefore in "Stand-by" mode, i.e. it is
powered and wai ng for the user to choose between the
following 4 hea ng modes.
The following TOUCH SCREEN commands are used to set the
desired hea ng mode.
accensione
Icon
stand-by
mode
Icon
funzioni
To ac vate one of the two commands, simply touch the icon
corresponding to the desired command with your finger. DO
NOT PRESS. When one of the switch-on modes is ac vated,
the device will emit a sound las ng approximately one
second.
COMFORT mode
Comfort mode is ac vated using the following procedure:
accensione
First touch on the
Ÿ
stand-by
into opera on at MINIMUM power and the LED at the
base of the product emits a BLUE LIGHT.
Second touch on the
Ÿ
radiator into opera on at MEDIUM power and the LED at
the base of the product emits a YELLOW LIGHT.
mode
Third touch on the
Ÿ
funzioni
into opera on at MAXIMUM power and the LED at the
base of the product emits a RED LIGHT.
Con nuing "TOUCHING" the
switches from one power to the other in the order
MINIMUM/Blue - MEDIUM/Yellow - MAXIMUM/Red.
To put the appliance into "Stand-by¹", simply touch the
accensione
mode
or
icon and the LED will in this case
stand-by
funzioni
emit a WHITE LIGHT.
To reac vate COMFORT mode, simply "touch" the
icon again and the product will switch on again in the same
posi on prior to being put into "Stand-by".
The product remains on but does not emit heat
2 hr "BOOST" mode
"Boost" mode automa cally switches on the product at
MAXIMUM power for 2 hours a er ac va on. A er this
period the device will return to "Stand-by¹" mode.
"Boost" mode is ac vated using the following procedure:
mode
Keep "touching" the
Ÿ
funzioni
seconds, un l you hear a SINGLE "BEEP" from the device,
confirming proper programming.
During opera on in "Boost" mode, the status LED of the
device will emit a flashing RED LIGHT.
cod. MAN#ORG. rev.00 - febbraio 2018
icon; this puts the radiator
mode
icon; this puts the
funzioni
icon; this puts the radiator
mode
icon, it automa cally
funzioni
accensione
stand-by
.
icon for between 3 and 6
To exit this mode and put the product into "Stand-by¹", simply
accensione
touch the
or
stand-by
LED will emit a WHITE LIGHT.
"TIMER_12" switch-on mode
The "Timer_12" mode lets you immediately ac vate the
"Boost" mode for two hours, a er which the device will go
into "Stand-by¹" mode for the following 10 hours² and then
ac vate the "Boost" func on again.
The "Timer_12" mode is ac vated using the following
procedure:
accensione
Touch the
icon once only and then keep
Ÿ
stand-by
mode
"touching" the
funzioni
un l you hear three consecu ve "BEEPS" from the device.
The cyclical nature of the "Timer_12" mode remains ac ve
for every day un l it is manually deac vated by the user by
accensione
simply touching the
stand-by
In this configura on, the status LED will emit a flashing RED
LIGHT when "Boost" is in opera on and a PURPLE LIGHT
during the "Stand-by" period.
²
During the first cycle, the "Stand-by" mode has a dura on of 9 hours.
"TIMER_24" switch-on mode
The "Timer_24" mode lets you immediately ac vate the
"Boost" mode for two hours, a er which the device will go
into "Stand-by¹" mode for the following 22 hours³ and then
ac vate the "Boost" func on again.
The "Timer_24" mode is ac vated using the following
procedure:
accensione
Touch the
icon once only and then keep
Ÿ
stand-by
"touching" the
mode
seconds, un l you hear TWO consecu ve "BEEPS" from
funzioni
the device.
The cyclical nature of the "Timer_24" mode remains ac ve
for every day un l it is manually deac vated by the user by
accensione
simply touching the
stand-by
In this configura on, the status LED will emit a flashing RED
LIGHT when "Boost" is in opera on and a PURPLE LIGHT
during the "Stand-by" period.
³
During the first cycle, the "Stand-by" mode has a dura on of 21 hours.
Prac cal example of se ng "TIMER_24"
I go into the bathroom to take a shower at 8.00 in the morning
and the bathroom is cold; I ac vate "TIMER_24", Origami starts
hea ng at maximum power for the next two hours and then goes
into "Stand-by", on the first day, for 21 hours (so un l 7.00 am the
next day), and then for 22 hours on all other days, un l
deac va on of the mode set. This means that the next day I can
go to take a shower again at 8.00 am but finding the bathroom
already warm since Origami, for all days subsequent to ac va on
of the "Timer_24" mode, will switch on from 7.00 am to 9.00 am.
mode
icon. In this case, the
funzioni
icon for more than 9 seconds,
mode
or
icon.
funzioni
icon for between 6 and 9
mode
or
icon.
funzioni
06
Publicidad
