Installation; Installing Loop Handle (02); Attaching The Carrying Strap To The Basic Appliance (03); Connecting/Separating Attachment And Basic Appliance (04) - AL-KO solo MT 42.2 Manual De Instrucciones

Installation

4 INSTALLATION
WARNING! Danger if assembly is not
carried out completely! Operation of an incom-
pletely assembled appliance can result in serious
injury.
■
Only operate the appliance when it is fully as-
sembled.
■
Do not insert the battery into the appliance
until it is fully assembled.
■
Check that all safety and protective devices
are in place and functioning correctly before
switching on.
4.1

Installing loop handle (02)

1. Place bracket (02/1) onto holder (02/2) on
shaft (02/3).
2. Place loop handle (02/4) onto the bracket
(02/a). The arrow (02/5) must be pointing in
the direction of the coupling.
3. Push spacer (02/6) under the loop handle on
the holder (02/2) (02/b).
4. Secure the loop handle and spacer with bolt
(02/7) and nut (02/8).
4.2 Attaching the carrying strap to the basic
appliance (03)
The carrying strap of your attachment transfers
the load of the attachment, shaft extension and
basic appliance to your upper body.
1. Hang the carrying strap (03/1) over your
shoulder.
2. Hook the snap hook (03/2) of the carrying strap
into the eye (03/3) on the basic appliance.
3. Adjust the length of the carrying strap by
moving the buckle (03/4) on the carrying
strap so that the whole appliance is comfort-
able to carry.
4. Carry out a number of work movements with
the appliance switched off to test the length
of the carrying strap. Adjust the length of the
carrying strap if necessary.
4.3 Connecting/separating attachment and
basic appliance (04)
Do not use more than one shaft extension.
Connecting attachment and shaft extension, if
necessary
1. Align the coupling (04/1) and coupling coun-
terpart (04/2) with each other so that the re-
cess (04/4) and journal (04/3) are facing one
another.
443441_a
2. Push coupling (04/1) and coupling counter-
part (04/2) completely into one another (04/a).
3. Push handle piece (04/5) completely over
coupling counterpart (04/2).
4. Turn the handle piece (04/c) up to the stop in
the direction of the closed padlock (04/6).
Separate the appliances and any extension
pipe from each other
1. Turn (04/d) the handle piece (04/5) towards
the open lock (04/7) to the end.
2. Pull coupling (04/1) and coupling counterpart
(04/2) apart (04/b).

5 START-UP

5.1

Charging the rechargeable battery

Observe the temperature range for charging, see
technical data.
NOTE For detailed information, see the sep-
arate operating instructions for the rechargeable
battery and the charger:
■
Operating manual 441630: Li ion recharge-
able battery B150 Li (B05-3640G), B200 Li
(B05-3650G)
■
Operating manual 441633: Charger C130 Li
(C05-4230)
5.2 Fitting and removing the rechargeable
battery (05)
Inserting the battery (05/a)
1. Push the battery (05/1) into the battery slot
(05/2) until it engages.
Pulling out the battery (05/b)
1. Press and hold the unlocking button (05/3) on
the battery.
2. Pull out the battery.

6 OPERATION

WARNING! Danger if assembly is not
carried out completely! Use of an incompletely
assembled appliance can result in serious injury.
■
Operate the appliance only when it is fully as-
sembled!
■
Do not insert the battery into the appliance
until it is fully assembled!
6.1 Switching the appliance on and off (06,
07)
Switching on the appliance
1. Bring the appliance into working position.
23