Publicidad
Idiomas disponibles
Idiomas disponibles
This manual is consistent with the date of manufacture
of your machine, you will find information on the
technical data of the machine acquired manual check for
updates of our machines on the website:
www.grupostayer.com
1_MACHINESPECIFIC SAFETY
WARNINGS
Use the tool only for pruning branches. Do not use it
for other tasks.
Never allow children or persons with disabilities of
any kind, as well as inexperienced persons to use
this tool. Failure to do so could result in injury.
Carefully read the instructions and specifications of
the battery you use with the tool. Failure to do so could
result in poisoning or injury when applying the product.
Always maintain a stable and balanced position. Do
not reach into hard-to-reach areas or work in awkward
positions.
Do not touch the scissor blades unless the battery is
disconnected. Failure to do so could result in injury.
Do not attempt to cut materials other than branches.
Cutting materials not intended for this tool may cause the
shears to jam. If this happens, disconnect the battery and
only then remove the jammed material.
Do not hold the branch to be cut with the hand that is
not holding the tool. For your safety always keep your
hand away from the cutting area and the tool.
Do not force the tool to cut beyond its capabilities.
The tool could slip and cut other things or injure you.
Avoid cutting any type of electrical wiring. Risk of
electrocution.
Handle the blades with extreme care. They are
extremely sharp and the tool is very powerful.
Always examine the blades before starting any work.
Bad or damaged blades can cause accidents.
After completing any work, switch the tool off at the
safety switch and disconnect the battery.
BATTERIES USE AND CARE
Do not open the battery. Danger of shortcircuiting.
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
Use the battery only in conjunction with your STAYER
power tool. This measure alone protects the battery
against dangerous overload.
Use only original STAYER batteries with the voltage
listed on the nameplate of your power tool. When using
other batteries, e. g. imitations, reconditioned batteries
or other brands, there is danger of injury as well as
property damage through exploding batteries.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The
battery can be damaged.
The battery is equipped with a temperature control
which allows charging only within a temperature range
of between 0 °C and 45 °C. A long battery service life is
achieved in this manner.
Observe the notes for disposal.
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the
first time.
The lithiumion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
The lithiumion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The
inserted tool no longer rotates.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot
be subject to overload. When the load is too high or
the allowable battery temperature range of 0–50 °C is
exceeded, the speed is reduced. The power tool will
not run at full speed until reaching the allowable battery
temperature. position. Unintentional actuation of the On/
Off switch can lead to injuries.
Open the keyless chuck 2 by turning in rotation direction
, until the tool can be inserted. Insert the tool. Firmly
tighten the collar of the keyless chuck 2 by hand in
rotation direction . This automatically locks the drill
chuck.
The locking is released again to remove the tool when
the collar is turned in the opposite direction.
2_FUNCTIONAL DESCRIPTION
PLACING OR FIXING THE TOOL
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
PRODUCT FEATURES
The numbering of the product features refers to the
illustration of the machine on the graphics page.
Screwdriver bit
1
Lower blade
2
Upper blade.
3
Hexagonal screw.
4
Trigger.
5
Tightening nut.
6
Safety switch I | O
7
Battery
8
Battery release button
9
Hexagon spanner
10 Lubricant
11 Internal hex spanner
-
11
-
es
it
gb
de
fr
p
tr
cz
el
Publicidad
