Technical Data; Unpacking; Assembly / Before Commissioning - Scheppach WSE3500 Traducción Del Manual De Instrucciones Original

6. Technical data

Dimensions L x W x H
Mains voltage U
1
Off-load voltage U
0
Working voltage U
2
Welding current l
2
Duty cycle X
Energy efficiency of the power
source
Power consumption in idle
state
Power consumption P1
Protection category
Insulation class
Type of cooling
Welding wire Ø
Weight of the welding wire
reel
Weight
Technical changes reserved!
7.

Unpacking

• Open the packaging and carefully remove the
device.
• Remove the packaging material, as well as the
packaging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, keep the packaging until the expiry of the
warranty period.
ATTENTION
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!
326 x 194 x 157 mm
230V~ / 50/60 Hz
31 V~
15.5 - 18.5 V~
30 - 90 A
30% - 90A
81%
30W
3300 W
H
IP 21S
AF
0.6 - 0.9 mm
max. 1 kg
5 kg
www.scheppach.com

8. Assembly / Before commissioning

Mounting the welding mask (Fig. 2 + 3)
Mount the handle (c) on the welding mask (a) as shown
in Fig. D.
Mount the protective glass (b) on the welding mask (a)
as shown in Fig. 3.
Then fold the three sides of the welding mask together.
The two side parts are connected to the top part by two
press studs.
Installing the welding wire reel (Fig. 4 - 7)
• Open the cover for the wire feeding device (5) by
pushing the lock (6) upwards.
Now you can see the wire feeding device and the
welding wire reel (Fig. 5).
• Unlock the reel mounting (d).
• Remove all packaging from the wire reel (d) so that
it can unroll freely.
• Fit the wire reel (d) onto the reel mounting. Ensure
that the reel will unwind on the same side as the wire
guide (h).
• Now press the adjustment screw (e) downwards and
fold the pressing roller (f) upwards. (Fig. 6)
• Unscrew cover (g) to check the feed roller.
• The corresponding wire thickness is marked on the
top side of the feed roller. If the size stipulated there
does not match with the actual wire thickness, turn
the feed roller or replace it if necessary.
• Now take the wire end off the edge of the reel and trim
it with side cutters or wire shears. Ensure that the
wire does not unroll.
• Now feed the wire through the wire guide (h) along the
feed roller and into the hose assembly fitting (fig. 6).
• Tension the pressing roller (f) again.
• Remove the burner nozzle (10) by simply pulling it
off. Unscrew the contact tip (12) too.
• Route the hose assembly (7) as straight as possible
as it runs away from the welding machine.
• Switch the welding machine on by setting the on/off
switch (14) to the "ON" position.
• Now press the burner button (9) to activate the wire
feed. Press the button until the wire emerges from
the front of the burner. When doing so, pay attention
to the feed roller. If this is slipping, re-tension the
pressing roller (f) with the adjustment screw (e).
Do not touch the welding wiring during this
procedure as there is a risk of injury with this!
• As soon as the wire projects ca. 5 cm from the front,
release the burner button again. Then switch the
machine off again and pull out the mains plug!
GB | 27