Publicidad
Idiomas disponibles
Idiomas disponibles
Skimmer WIDE
For the pool frame of concrete - covered with tile/mosaic
Consult your concrete/waterproofing supplier for any waterproofing and application method.
2
1
13
15
Installation as following:
NOTE! When casting/reinforcing the pool frame work, do not get closer than at
least 50 mm to the stainless materials.
1. Make a hole for the skimmer in the framework, dimensions and placement as
shown in Figure 2.
2. Apply sealer at the joint between the sealing flanges and the skimmer housing
(see Fig. 9).
Pahlén recommends Tec7 as a sealant from Novatech (available from Pahlén) or
Aqua Max from Griffon.
Upon application of the sealant, it is important that the joints are tight, so that no
water can penetrate.
See sealant instruction for preparation, application and hardening.
3. Fasten the skimmer in the mold, so that the flange is in contact with the concrete wall.
NOTE! Non-corrosive material (e.g. steel) may not be closer to the stainless steel
(pipe) than 50 mm.
4. Connect the cable (at least 6 mm²) with a ring from the intake flange to earth
(see item 3 Figure 8). Screw, toothed washer and nut are supplied with the product.
If other components are used, it must be ensured that they are of stainless steel
quality (Min. A4).
5. Prior to sealing; mask the skimmer exposed flange and openings in order to avoid
unsightly stains from concrete splashes.
The openings in the skimmer back edge of the float switch, the overflow and refill
openings can be sealed with supplied plugs, see Fig.11
6. Seal the pool frame.
7. Mount the wall cladding (fix, tile, mosaic, etc.). Make sure that the mounting holes
(see Fig. 10) for fastening the frame are free, so that the mounting frame can be
installed later.
8. Check that the flap cap is properly in place and can move.
9. Assemble the frame and secure it with screws (4x M5x30), see Fig. 8.
10. Mount the front of the frame and secure it with the supplied screws (4x M5x12) in the second and eighth holes, see Fig. 12.
11. Connect the pipe coupling to the
pool circulation with an appropriate
thread sealant.
12. The position of the skimmer top
should be adjusted in height to the
flooring around the pool. Fix to the
desired height with attached straps.
13. If the skimmer top is shortened or
processed in any other way,
tools only for stainless materials
should be used.
3
5
4
6
7
1
9
17
12
10
1. Fixing strip with a screw M5x12 (2x)
2. Skimmer top
3. Earthing point
4. Countersunk screw M6x30 (4x)
5. Mounting frame
6. Countersunk screw M5x12 (4x)
7. Front
8
8. Flange
1
9. Concrete
9
6
10. Reinforcing bar
10
6
Fig 8.
Surface treatment
Designed by:
Drawn by: Date
E
TK
The tolerance class in accordance with this
Assembly drawing no.
Art.no.
part of ISO 2768-mK
Scale
Installationsbild bräddavlopp WM
För poolstomme av thermoblock
Drawing number
Box 728, SE-194 27 Upplands Väsby, Sweden
Phone +46 8 59411050, Fax +46 8 59086880
13
10
11
9
8
10
Approved by:
2016-11-15
Revised by: Date
Rev.no.
M12627 0
Surface treatment
E
The tolerance class in accordance with this
part of ISO 2768-mK
Box 728, SE-194 27 Upplands Väsby, Sweden
Phone +46 8 59411050, Fax +46 8 59086880
12
20
19
1
3
Flap cap
2
A
7
5
Concrete wall
6
4
Surface treatment
E
The tolerance class in accordance with this
part of ISO 2768-mK
Box 728, SE-194 27 Upplands Väsby, Sweden
Phone +46 8 59411050, Fax +46 8 59086880
ENGLISH
Fig 9.
2
8
Designed by:
Drawn by: Date
Betad
TK
2016-01-26
Art.no.
Assembly drawing no.
15594075
Bräddavlopp WM
Scale
Fig 10.
1:4
Drawing number
M12533 0
21 22 23
24
Fig 11.
Fig 12.
A
Screw
14
15
Front
16
17
Mountning
frame
Tail/Mosaic
Tail join
Tail fix
Designed by:
Drawn by: Date
Approved by:
TK
2016-11-15
Assembly drawing no.
Art.no.
Scale
Revised by: Date
Installationsbild bräddavlopp WM
För poolstomme av thermoblock
Drawing number
Rev.no.
M12627 0
Approved by:
Revised by: Date
Rev.no.
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
18
8
7
6
5
4
3
2
1
Item
B
P
Publicidad
