Automatic dehumidification:
Please press the mode button (7) to switch on the automatic dehumidification function; the corresponding
•
indicator lights up.
•
The desired humidity level can be set between 30% and 80% in 5% steps by pressing the humidity level
button (6).
Press the fan speed button (3) to select between high and low wind speed.
•
If the ambient humidity is 5% lower than the set humidity level, only the fan function will be activated. As
•
soon as the room humidity gets 5% higher than the set value, the compressor will start automatically.
Continuous dehumidification:
Please press the mode button (7) to switch on the continuous dehumidification function. This mode can be
•
used without regard to the ambient humidity level. To select between high and low fan speed, please press
the fan speed button (3). The humidity level cannot be set in this mode.
Internal drying:
Please press the internal drying button (2) to activate this function. The drying process takes about one hour
•
and prevents the growth of mold.
During internal drying, the message "CL" is continuously shown on the display and all other modes are
•
turned off.
To stop the drying process, please press the button (2) again. The unit will automatically get back to the
•
operation with previous settings.
To stop the internal drying and switch the unit into stand-by mode, please press the On/Off button.
•
Timer:
Please press the timer button (1) to set the timer from 0 to 24 hours. It takes about 5 seconds until the mode
•
is set, during this time the timer key will not be available. Please set the desired mode before.
When the unit is switched on, press the timer button to set the shut-off time as described above. The timer
•
indicator will light up.
•
When the unit is switched off, press the timer key to set the switch-on time as described before. The timer
indicator will light up and the selected time will be shown on the display.
Child Lock
Please press and hold the mode button (7) for 3 seconds to switch the child lock on or off.
•
Sleep Mode:
Please press and hold the "Internal Drying" button (2) for 3 seconds to disable/enable sleep mode.
•
In sleep mode, all indication lights are turned off, the device works automatically at low wind speed and
•
target humidity 50%. The settings cannot be changed manually in sleep mode. Please switch on the timer
as described above, the sleep mode will be deactivated.
If the ambient humidity is high, the unit will dehumidify with the low wind speed; if the ambient humidity is
•
low, the compressor will stop working, only the ventilation function will be activated.
To deactivate the sleep mode, please press the mode key, internal drying key or the on/off key.
•
Wi-Fi:
• When connecting the device, the WLAN indicator (9) will start blinking.
• The WIFI function can only be activated in standby mode. Please press and hold the humidity level button
(6) for 3 seconds to start WIFI mode. The display will start blinking rapidly to search for devices to pair.
• Please follow the step-by-step instructions in the app to connect your device to the WIFI and set up the
control.
Resetting the WIFI in case of connection errors and for new connections
If you want to connect the device to a new WLAN or if there are problems when trying to connect the device
•
to the app, it is necessary to reset the WLAN.
If the WiFi indicator is not blinking: Please hold the humidity level button (6) in standby- mode for 3 seconds.
•
The device must be switched on . A signal sounds 3 times and the device is ready to be connected to the
app again.
Please follow the step-by-step instructions in the app to connect your device to the Wi-Fi and set up the
•
control.
Drainage
Water tank:
As soon as the water tank is full, the unit stops working, a warning signal sounds, the 'water tank full' indicator
•
(4) lights up on the control panel and error message "FL" will be shown on the display.
Please switch off and unplug the unit.
•
•
Please pull out the water tank carefully, open the lid of the water tank by
using the lever and empty the water.
•
Please clean the empty tank, close the lid and then carefully push it back
into the device.
Continuous drainage:
Please pull the plug out of the outlet.
•