Publicidad
Idiomas disponibles
Idiomas disponibles
Change light color
With lights and motor turned Off, press and hold light button
for 3 sec, both buttons will fully illuminate on the current light
color� The buttons can be used to select desired color (Light
<< button backwards, Blower button forward >>)
Available light colors are white (default color), blue, green or
red� To set color, choose one and press both buttons at the
same time�
CFM Reduction System
Before operating your hood:
Some States and Provinces of the US & Canada restrict the
maximum exhausting airflow of range hoods�
Airflow is measured as cubic feet per minute (CFM)�
These maximum levels allowed are detailed in the local code
of your area� Please check local codes to find out if you need
to restrict the maximum airflow of your hood� If your local
code mandates a maximum airflow level below the maximum
airflow of this hood (i�e� 400 CFM), please execute the
procedure below to reduce the maximum airflow�
With blower and light turned Off
• Press and hold both buttons at the same time for 3 sec you
will hear a beep and the icon lights (no edge) will illuminate
for 3 seconds�
• This action will disable speed 4 and effectively lower the
maximum airflow to > 300 CFM�
• Locate the CFM certification sticker in the hardware pack�
• Peel and Affix this sticker to a visible area in the blower�This
sticker provides official certification to your local inspector
that this hoods maximum airflow has been reduced to >
300 CFM�
Maintenance
Cleaning
IMPORTANT: Clean the hood and grease filters frequently
according to the following instructions� Replace grease filter
before operating the hood�
Exterior surfaces
To avoid damage to the exterior surface, do not use steel wool
or soap-filled scouring pads�
Always wipe dry to avoid water marks�
Cleaning method:
•
Liquid detergent soap and water, or all-purpose cleanser
•
Wipe with damp soft cloth or nonabrasive sponge, then
rinse with clean water and wipe dry�
Metal grease filter
The filters should be washed frequently� Place metal filters in
dishwasher or hot detergent solution to clean� Let filter dry
throughly before replacing it�
Turn off fan and lights� Allow lamps to cool�
1
Remove each filter by pulling the spring release handle
and then pulling down the filter�
A
12
A. Spring handle release
Sound
To enter sound mode, with lights and motor turned Off
press both buttons at the same time and the upper left
corner of the light button will illuminate with white light� The
buttons can be used to select desired sound (Light <<button
backwards, Blower button forward>>)�
Available feedback sounds are regular beep, soft beep and
mute� As the regular and soft beep are selected, the hood
will reproduce each sound� When mute is selected, upper left
corner of the light button will illuminate with red light� To set
sound, choose one and press both buttons at the same time�
Indicators of filter saturation:
At regular time intervals, the hood indicates the need of
performing filter maintenance�
Blower button icon blink (no edge):
Perform grease filter maintenance�
Light button blink (no edge):
Perform activated charcoal filter maintenance�
Reset of filter saturation indicators:
With blower Off press and hold the blower button for 3 sec�
Activation of saturation indicator activated charcoal filter:
NOTE: This operation must be performed with the hood off�
This indicator is normally deactivated; press and hold the
blower button for 3 sec� to activate the function: the button
blinks for 1 sec�
To deactivate the function, press and hold the blower button
for 3 sec�, the button blinks for half a sec�
2
Wash metal filters as needed in dishwasher or hot deter-
gent solution�
3
Reinstall the filter by making sure the spring release
handles are toward the front� Insert metal grease filter into
upper track�
4
Pull the spring release handle down�
5
Push up on metal filter and release handle to latch into
place�
6
Repeat steps 1-5 for the other filter�
Replacing a LED lamp
The LED lights are replaceable by a service technician only�
See "Who to contact" section in the warranty for service
contact information�
Publicidad
