Publicidad
Idiomas disponibles
Idiomas disponibles
machined component) to ensure that the coarse-
ness and type of sanding sheet 7, as well as the
oscillation frequency of the sanding plate 6 have
been selected properly.
• Ensure that the element to be sanded is firmly se-
cured�
• Turn on the power tool earlier, before sanding
plate 6 touches the element to be sanded and allow
the engine of the power tool to reach maximum oscil-
lation rate�
• Apply sanding plate 6 to the surface of the machined
element and move the power tool in circular or recip-
rocating motion�
• Perform sanding with the whole surface of sanding
plate 6�
• Do not press the power tool excessively, since this
will not provide better results, but will only overload the
engine of the power tool and will result in higher sand-
ing sheet 7 consumption�
• Do not stop the power tool in a single spot this will
result in a depression in the stoppage place�
• At relevant time, replace the used or dust-blocked
sanding sheets 7�
• Use sanding sheets 7 of varying coarseness com-
mence the work with a coarse sheet and gradually pro-
ceed to finer sheets. It will make the work faster and
will result in smoother surface�
• Do not reuse sanding sheets 7 that were previously
used for sanding metal for any other materials�
Polishing
[EX03-125 DV]
During polishing, it is recommended
to set lower oscillation frequency of
sanding plate 6 - this will prevent the
overheating of machined surface. Prior
to commencement of work, perform test polishing
to ensure whether the polishing agent and oscil-
lation frequency of sanding plate 6 have been se-
lected properly.
• Apply the polishing agent to the machined surface�
• Attach polishing sponge 11 to the sanding plate 6 in
the manner described above�
• Turn on the power tool and spread the polishing
agent on the machined surface� Subsequently, per-
form the polishing with circular or cross movements
with little pressure�
• Turn off the power tool, remove polishing sponge 11
and attach polishing bonnet 12 to sanding plate 6�
• Using a soft cloth, remove excess polishing agent
from the machined surface and perform final polishing
with polishing bonnet 12, with circular or cross move-
ments with little pressure�
The manufacturer reserves the possibility to introduce changes.
• After the work is completed, rinse polishing
sponge 11 and polishing bonnet 12 in warm water with
a cleaning agent� Do not use solvents.
• Squeeze (do not wring) polishing sponge 11
and polishing bonnet 12� Allow them to dry, stretch-
ing them on flat surface, adhesive surface on
the bottom� Attention: do not store the polish-
ing accessories unless they have dried out
completely.
Before carrying out any works on the power tool it
must be disconnected from the mains.
Cleaning of the power tool
An indispensable condition for a safe long-term exploi-
tation of the power tool is to keep it clean� Regularly
flush the power tool with compressed air thought the
ventilation slots 3�
After-sales service and application service
Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts� Information about service centers,
parts diagrams and information about spare parts can
also be found under: www.dwt-pt.com�
•
Categorically not to drop any mechanical impact on
the packaging during transport�
• When unloading / loading is not allowed to use any
kind of technology that works on the principle of clamp-
ing packaging�
Recycle
disposing as waste.
Power tool, accessories and packaging
should be sorted for environment-friendly
recycling�
The plastic components are labelled for categorized
recycling�
These instructions are printed on recycled paper man-
ufactured without chlorine�
English
Автотовары «130»
22
Power tool maintenance /
preventive measures
Transportation
of the power tools
Environmental
protection
raw
materials
instead
of
Publicidad
