Partner K650 ACTIVE II EPA Manual De Instrucciones
Ocultar thumbs
Ver también para K650 ACTIVE II EPA:
- Manual de instrucciones (47 páginas) ,
- Manual de instrucciones (24 páginas)
Publicidad
Enlaces rápidos
All manuals and user guides at all-guides.com
Eng
F
Esp
K650 ACTIVE II EPA
K700 ACTIVE II EPA
Operator's manual
Read these instructions carefully and make sure you
understand them before using the machine.
Manuel d'utilisation
Lire attentivement et bien assimiler le manuel d'utilisation
avant de se servir de la machine.
Manual de
instrucciones
Antes de utilizar la máquina, lea bien el manual de
instrucciones hasta comprender su contenido.
Publicidad
Manuales relacionados para Partner K650 ACTIVE II EPA
Resumen de contenidos para Partner K650 ACTIVE II EPA
- Página 1 All manuals and user guides at all-guides.com K650 ACTIVE II EPA K700 ACTIVE II EPA Operator’s manual Read these instructions carefully and make sure you understand them before using the machine. Manuel d’utilisation Lire attentivement et bien assimiler le manuel d’utilisation avant de se servir de la machine.
-
Página 2: Tabla De Contenido
All manuals and user guides at all-guides.com Contents Replacing the starter cord ......16-17 Foreword ............... 1 Replacing the starter spring ........ 18 Symbols in the operating instructions ....2 Air filter ............19-20 Symbols on the power cutter ........ 3 Carburettor ............. -
Página 3: Foreword
All manuals and user guides at all-guides.com Foreword The power cutter is a machine with a high cutting capacity and it is fitted with safety features to make the work carried out as safe as possible. If the safety WARNING! features are out of operation or if the machine is used Use only cutting wheels approved for use with carelessly or wrongly, the result can be injuries... -
Página 4: Symbols In The Operating Instructions
All manuals and user guides at all-guides.com Symbols in the operating instructions WARNING! This power cutter can be Study the operating instructions carefully dangerous. and make sure that you understand the Careless or incorrect use of this machine can contents before using the power cutter. result in serious, even fatal, injuries. -
Página 5: Symbols On The Power Cutter
All manuals and user guides at all-guides.com Symbols on the power cutter WARNING! The power cutter can be Warning dangerous! Careless and incorrect use can Cutting creates a lots of dust which result in serious, even fatal injury. can cause inhalation damages. Use appropriate dust mask or respirator protection. -
Página 6: Operator Safety Precautions
All manuals and user guides at all-guides.com Operator Safety Precautions 1. Never operate the machine when you are 5. Never start cutting until you have a clear work area tired, angry, emotionally disturbed, or under the and secure footing. influence of alcohol, drugs, medication, or 6. - Página 7 All manuals and user guides at all-guides.com 11. Never operate a cutting machine that is damaged, 17. Operate the machine only in well-ventilated areas. improperly adjusted, or not completely and Failure to use the power cutter in a well-ventilated securely assembled. Be sure that the wheel stops area can lead to serious injury or death.
-
Página 8: Identification
All manuals and user guides at all-guides.com Identification Identification Denominacion... -
Página 9: Identification
All manuals and user guides at all-guides.com Pos. Description 1. Cutter disc 11. Cover for air filter 2. Guard 12. Air filter 3. Knob for guard adjustment 13. Spark plug (under cover) 4. Stop switch 14. Decompression valve 5. Choke 15. -
Página 10: Reversing The Cutting Arm
All manuals and user guides at all-guides.com Reversing the cutting arm It is possible to reverse the cutting arm 180 Turn the arm 180 and then refit parts and screw that the cutter wheel is positioned on the into position as earlier. Note that the flange opposite side of the arm. -
Página 11: Cutting Wheel
All manuals and user guides at all-guides.com Cutting wheel The cutting wheel is tightened with the fixed The wheel is placed between the flange washer wrench 501 69 17-02, that is delivered with the A and B. Check the arbor bushing so that it corresponds with the size of the hole in the power cutter. -
Página 12: Discue Découpeur
All manuals and user guides at all-guides.com The spindle is secured by means of pin WARNING! 503 24 06-02, which is pushed in as far as Never operate without the wheel guard. possible. The wheel is tightened clockwise. The guard should be adjusted so that its rear section is close to the workpiece. -
Página 13: Drive Belt
All manuals and user guides at all-guides.com Drive belt The belt is completely enclosed and well Adjust the tensioning screw so that the nut is protected from dust and dirt as well as from positioned at the arrow marked on the cover. mechanical damage during cutting work. -
Página 14: Fuel Filter
All manuals and user guides at all-guides.com Fuel filter To replace the belt loosen the two nuts and then Wipe the area around the fuel cap clean before the tensioning screw until the tension is released. the filler cap is removed. Dirt in the fuel tank will Remove the nuts and the belt cover. -
Página 15: Fuel Mixture
• Change your clothes if you should spill petrol on yourself. For the best results, use Partner’s two-stroke oil. Mixture: 2%. • Move the machine at least three metres Never use oil that is intended for four-stroke engines. -
Página 16: Controls
All manuals and user guides at all-guides.com Controls catch. Release the throttle control and the A Stop switch. When the button is pressed throttle is blocked in half throttle position. The backwards, the engine stops. The button remains in this position and must be returned catch is released when the throttle control is pressed in all the way. -
Página 17: Startinging The Engine
All manuals and user guides at all-guides.com Starting the engine WARNING! Make sure the stop switch (A) is in running The cutting wheel will start to rotate when the position (pushed forward). Pull the choke control saw starts. Make sure that the cutting wheel (B) if the engine is cold. -
Página 18: Replacing The Starter Cord
All manuals and user guides at all-guides.com Replacing the starter cord 1. Remove the air filter and cylinder cover. 3. Pull out the starter cord a little and prevent the pulley from rotating backwards. 2. Remove the four screws and lift away the starter. -
Página 19: Pour Remplacer Le Cordon De Démarrage
All manuals and user guides at all-guides.com 5. Remove the locking spring or screw and lift up 10. Mount the locking spring or screw. the starter pulley. 11. Wind three turns of the starter cord round the 6. Pull the new starter cord through the hole in the pulley. -
Página 20: Replacing The Starter Spring
All manuals and user guides at all-guides.com Replacing the starter spring 1. Follow the same procedure as described WARNING! above for replacement of the starter cord. When the recoil spring is assembled in the starter housing, it is in tensioned position and 2. -
Página 21: Air Filter
All manuals and user guides at all-guides.com Air filter The filter system consists of a centrifugal cleaning The main filter (2) is removed by means of nozzle (1), main filter (2) and protective filter (3). loosening the two screws which hold the filter The main filter is an oil saturated foam filter and cover. - Página 22 All manuals and user guides at all-guides.com Air filter The protective filter (3), which is a paper filter, is When dismantling the cylinder cover it is mounted in the cylinder cover under the filter base. important to check that the seal D is in good This filter must only be shaken clean.
-
Página 23: Carburettor
All manuals and user guides at all-guides.com Carburettor Jets Governor The carburettor is equipped with fixed jets to The engine is equipped with a carburettor which ensure the engine always receives the correct fuel- has a built-in governor. At the maximum speed, air mixture. -
Página 24: Carburateur
All manuals and user guides at all-guides.com Idling speed (T) If an adjustment is necessary, adjust with the WARNING! screw marked T on the cover. Adjust the idle Contact your servicing dealer if the idle speed so that the cutter wheel does not rotate. A adjustment cannot be adjusted so that the correctly adjusted idle speed setting (approx. -
Página 25: Spark Plug
All manuals and user guides at all-guides.com Spark plug If the engine is low on power, difficult to start or IMPORTANT! runs poorly at idling speed, always check the Always use the recommended spark plug type, spark plug first. If the spark plug is dirty, clean it Champion RCJ-7Y or NGK BPMR 7A. -
Página 26: Técnica De Trabajo
All manuals and user guides at all-guides.com Working technique When cutting stone, concrete and similar mate- When cutting steel and other metals, always try rial the wheel should be moved forwards and to maintain high cutting pressure and high wheel backwards in the cut to obtain good conduction speed. -
Página 27: Maintenance Scheme
All manuals and user guides at all-guides.com Maintenance scheme The following is a summary of various measures mentioned in the book and which is essential for the correct servicing of the power cutter. The time intervals mentioned should be applied if the power cutter is used for at least 4 hours every day. -
Página 28: Tools
All manuals and user guides at all-guides.com Esquema de mantenimiento A continuación se muestra un sumario de las distintas medidas mencionadas en el libro y las cuales son esenciales para un servicio correcto de la máquina. Los intervalos de tiempo mencionados deberán ser aplicados si la máquina se ha usado por lo menos cuatro horas cada día. -
Página 29: Technical Data
Speed governor Tillotson HS-175H Tillotson HS-175H Range of regulations 10.000±400 10.000±400 Fuel Oil mixture ratio with Partner oil 2% (1:50) 2% (1:50) Tank capacity 0,76 l (26 oz) 0,76 l (26 oz) Weight 9,3 kg (20.5 lb) 9,9 kg (21.8 lb) Cutting wheel 12"... -
Página 30: Données Techniques
0,5 mm 0,5 mm Carburateur Régulateur Tillotson HS-175H Tillotson HS-175H Plage de réglage 10.000±400 10.000±400 Carburant Mélange à lubrifiant avec huile Partner 2% (1:50) 2% (1:50) Capacité de réservoir 0,76 l 0,76 l Poids 9,3 kg 9,9 kg Disque de coupe 12"... -
Página 31: Datos Técnicos
0,5 mm Carburador Regulador por velocidad Tillotson HS-175H Tillotson HS-175H Gama de regulación 10.000±400 10.000±400 Combustible Mezcla de combustible con aceite Partner 2% (1:50) 2% (1:50) Capacidad del depósito 0,76 l 0,76 l Peso 9,3 kg 9,9 kg Disco de corte 12"... -
Página 32: Safety Rule Checklist
All manuals and user guides at all-guides.com Safety rule checklist Operation Operator Before start • Controls work smoothly and correctly. • Is fully instructed in use of the power cutter. • Tank filled min. 3 m (10 feet) away from cutting •... -
Página 33: Liste De Contrôle, Prescriptions De Sécurité
All manuals and user guides at all-guides.com Liste de contrôle, prescriptions de Utilisation sécurité Avant la mise en route • Les commandes fonctionnent sans remarque. L’utilisateur devra • avoir appris comment utiliser la découpeuse • Le réservoir de carburant est rempli au moins à 3 mètres du lieu de travail. -
Página 34: Lista De Chequeo De Seguridad
All manuals and user guides at all-guides.com Lista de chequeo de seguridad Funcionamiento Usuario Antes del arranque • Controlar que los mandos se accionan con facilidad • Ha sido instruido en el manejo de la máquina. y correctamente. • Ha léido y comprendido este manual de seguridad y •... -
Página 35: Federal Emission Control Warranty Statement
Repair or replacement of any warranted part will be perfor- The EPA (The US Environmental Protection Agency) and med at no charge to the owner at an approved Partner Partner Industrial are pleased to explain the emissions Industrial servicing dealer. If you have any questions... - Página 36 All manuals and user guides at all-guides.com 108 87 68-79 ´*xlw¶9k¨ 1998W50...