Electrical Safety; Assembly - ATIKA LSH 3000 Manual Original

Switch the machine off and remove the mains plug from
the socket when
− carrying out repair works
− carrying out servicing and repair works
− removal of faults
− eliminating blockages
− checking the leads to see whether these
are caught up or damaged
− changing over from vacuuming to blowing
− transporting
− leaving unattended (even during short interruptions)
− unusual noises and vibrations
Thoroughly maintain your garden vac:
− Make sure that the ventilation apertures are free.
− Keep handles dry and free of oils and grease.
− Follow the maintenance instructions and the
instructions for spool exchange.
Check the machine for possible damage
− Before continuing to use the machine, the protective
devices must be inspected to ensure that they work
perfectly and with their intended function
− Check whether the parts are damaged. All parts must
be correctly installed and fulfil all conditions to ensure
perfect operation of the saw.
− Damaged guards and parts must be properly repaired
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
− Damaged or illegible safety warning labels should be
replaced immediately.
Store the unused machine in a dry locked place away from
the reach of children.

Electrical safety

Design of the connection cable according to IEC 60245 (H
07 RN-F) with a core cross-profile section of at least
− 1.5 mm² for cable lengths up to 25 m
− 2.5 mm
for cable lengths over 25 m
2
Long and thin connection lines result in a potential drop.
The motor does not reach any longer its maximal power;
the function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with
this material.
The connector of the connection cable must be splash-
proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Wind off completely the cable when using a cable drum.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges.
Do not use the cable for machine carrying and hanging up
or for pulling the plug out of the socket.
Protect yourself against electric shocks. Avoid touching
earthed parts with your body (e.g. pipes, heating
apparatus, cookers, fridges etc.).
13
All manuals and user guides at all-guides.com
Do never connect a damaged cable to the mains. Do not
touch a damaged cable before it is disconnected from the
mains. A damaged cable may cause contact with live
parts.
Do not use any defective connection cables.
When working outdoors, only use extension cables
especially approved and appropriately labelled for outdoor
use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current
circuit breaker (30 mA).
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician
or one of our customer service points. Local regulations
– especially regarding protective measures – must be
observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service
points.
Use only original spare parts. Accidents can arise for the
user through the use of other spare parts. The
manufacturer is not liable for any damage or injury
resulting from such action.

Assembly

Please observe the enclosed assembling
instructions!
Connect the leaf sucker to the power
supply system only after having finished
the complete assembly.
Assembling the suction tube
2 Connect the front (11) on the rear suction tube (10)
and screw them together.
Then, insert the completed suction tube (10+11) in the
machine body (5) and screw both together.
Please make sure that the connectors C and D are
connected to each other!
Fixing the collecting bag
3 At first, hook up the front end of the collecting bag (12)
on the suction tube (11).
Finally, slip the opening of the collecting bag (12) on
the dedicated opening on the machine body (5).
Fixing the carrying strap
4 Put the loop of the carrying strap (7) through the
provided opening on the machine body (5).