Publicidad
Idiomas disponibles
Idiomas disponibles
BEFORE EACH USE
•
Check engine oil level.
•
Check water inlet screen for damage.
•
Check high pressure hose for leaks.
•
Check chemical tanks and filters for damage.
•
Check spray gun and nozzle extension assembly
for leaks.
•
Purge pump of air and contaminants.
PRESSURE WASHER MAINTENANCE
Check and Clean Inlet Screen
Examine garden hose inlet screen. Clean if it is
clogged or replace if it is torn.
Check High Pressure Hose
High pressure hoses can develop leaks from wear,
kinking, or abuse. Inspect hose before each use.
Check for cuts, leaks, abrasions, bulging of cover, or
damage or movement of couplings. If any of these
conditions exist, replace hose immediately.
CAUTION!
Never repair a high pressure hose.
Replace with hose that exceeds the maximum
pressure rating of your cleaning system.
Check Chemical Reservoirs
Tank covers should snap cleanly onto tank. Ensure
chemical labels correctly identify tank contents.
Ensure that the System Rinse tank is filled with clean
water. Ensure that Dial-A-Cleaner™ selector knob
rotates freely between each position. Examine the
tanks and replace if the filter is clogged.
Check Gun and Nozzle extension
Examine hose connection to spray gun and make sure
it is secure. Test trigger by pressing it and making
sure it springs back into place when you release it. Put
safety latch in UP position and test trigger. You should
not be able to press trigger. Replace spray gun
immediately if it fails any of these tests.
Check In-Line Filter
Refer to the illustration and service the in-line filter if it
becomes clogged, as follows:
Nozzle Extension
1. Detach spray gun and nozzle extension from high
pressure hose. Detach nozzle extension from spray
gun and remove o-ring and screen from nozzle
extension. Flush the screen, spray gun, and nozzle
extension with clean water to clear debris.
2. If the screen is damaged, the o-ring kit contains a
replacement in-line filter screen and an o-ring. If
undamaged, reuse screen.
3. Place the in-line filter screen into the threaded end
of the nozzle extension. Direction does not matter.
Push the screen in with the eraser end of a pencil
until it rests flat at the bottom of the opening. Take
care to not bend the screen.
4. Place the o-ring into the recess. Push the o-ring
snugly against the in-line filter screen.
5. Assemble the nozzle extension to the spray gun,
as described earlier in this manual.
Purge Pump of Air and Contaminants
To remove air from the pump, follow these steps:
•
Set up the cleaning system as described in the
"Assembling Your Cleaning System" and connect
the water supply.
•
Pull the trigger on the spray gun and hold until a
steady stream of water appears.
To remove contaminants from the pump, follow these
steps:
•
Set up the cleaning system as described in the
"Assembling Your Cleaning System", and connect
the water supply.
•
Remove the nozzle extension from the spray gun.
•
Start the engine according to instructions in "How
To Use Your Cleaning System".
•
Pull the trigger on the spray gun and hold.
•
When the water supply is steady and constant,
engage the safety latch and refasten the nozzle
extension.
Nozzle Maintenance
A pulsing sensation felt while squeezing the spray gun
trigger may be caused by excessive pump pressure.
The principal cause of excessive pump pressure is a
nozzle clogged or restricted with foreign materials,
such as dirt, etc. To correct the problem, immediately
clean the nozzle using the tools included with your
pressure washer and follow these instructions:
1. Shut off the engine and turn off the water supply.
2. Remove the nozzle from the end of the nozzle
extension. Separate the nozzle extension from the
spray gun. Twist the nozzle clockwise to the stream
position. Using the supplied 2mm (5/64) allen
wrench, remove the nozzle from the end of the
nozzle extension.
In-line Filter
O-ring
3. Remove the in-line filter from the other end of the
nozzle extension.
4. Use the wire included in the kit (or a small paper
clip) to free any foreign material clogging or
restricting the nozzle.
12
Publicidad
