Publicidad
Idiomas disponibles
Idiomas disponibles
•
Do not use the guard for handling or transportation.
•
Do not exert side pressure on the saw blade.
•
Never cut light alloy. The machine is not designed for
this application.
•
Do not use abrasive disc or diamond cutting wheels.
•
Rabbeting, slotting or grooving is not allowed.
•
In case of machine failure, immediately switch the machine
off and remove from the power source. Report the failure and
mark the machine in suitable form which prevents that other
persons use the defective machine.
•
When the saw blade is blocked due to abnormal feed force
during cutting, ALWAYS switch the machine off and remove
from the power source. Remove the workpiece and ensure that
the saw blade runs free. Turn the machine on and start a new
cutting operation with reduced feed force.
•
NEVER attempt to cut a stack of loose pieces of material
which could cause loss of control or kickback. Support all
materials securely.
•
Take care that the blade guard is properly positioned. When
sawing, it must always face against the workpiece.
Saw Blades
•
Do not use saw blades that do not conform to the dimensions
stated in the Technical Data. Do not use any spacers to make a
blade fit onto the spindle. Use only the blades specified in this
manual, complying with EN847-1, if intended for wood and
similar materials.
•
The maximunm speed of the saw blade shall always be
greater than or at least equal to the speed marked on the
rating plate of the tool.
•
The saw blade diameter must be in accordance with the
markings on rating plate of the tool.
•
Consider applying specially designed noisereduction blades.
•
Do not use high steel (HS) saw blades.
•
Do not use cracked or damaged saw blades.
•
Ensure that the chosen saw blade is suitable for the material
to be cut.
•
Always wear gloves for handling saw blades and rough
material. Saw blades should be carried in a holder
wherever practicable.
Power connections
Before connecting the machine to the power line, make sure
the switch (8) is in the "OFF" position and be sure that the
electric current is of the same characteristics as indicated on
the machine. All line connections should make good contact.
Running on low voltage will damage the machine.
DANGER! Do not expose the machine to rain or operate
the machine in damp locations.
Before connecting the machine to the power source, make sure
the switch is in the "OFF" position.
SAFETY OF OTHERS
•
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
•
Children should be supervised to ensure that they do not play
with the appliance.
Residual Risks
WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
•
Impairment of hearing.
•
Risk of personal injury due to flying particles.
•
Risk of burns due to accessories becoming hot
during operation.
•
Risk of personal injury due to prolonged use.
SAVE THESE INSTRUCTIONS
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your STANLEY tool is double insulated in accordance
with EN62841; therefore no earth wire is required.
T his product is intended to be used with a safety transformer
manufactured to BSEN61558 and BS4343. Never work without
this transformer in place.
If the supply cord is damaged, it must be replaced only by
STANLEY or an authorised service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
•
Safely dispose of the old plug.
•
Connect the brown lead t o the live terminal in the plug.
•
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
Package Contents
The package contains:
1 Table saw
1 60T saw blade
ENGLISh
; the
2
33
Publicidad
