Good Earth Lighting GL1326-WHT-24LFC-G Manual

Push Buttons
Boutons poussoirs.
Botones pulsadores
Power Cord
Cordon d'alimentation
Cable de alimentación
Linking Cord
Cordon de raccordement
Cable de enlace
READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!
WARNING: TO AVOID ELECTRIC SHOCK, DISCONNECT POWER BEFORE INSTALLING!
WARNING: DO NOT attempt to alter the fixture. The fixture is not manufactured
with parts that are serviceable or replaceable.
WARNING: BURN HAZARD! The fixture can be hot; allow cooling time prior to
touching.
WARNING: DO NOT ALTER THE PLUG OR CORD. This LED light has a
polarized plug (one blade is wider than the other) as a feature to reduce the risk
of electric shock. This plug will only fit in a polarized outlet one way. If the plug
does not fully fit in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Never use a power strip unless the plug can be fully inserted.
WARNING: Products should be installed following these instructions, local
electrical codes, and/or the current National Electric Code (NEC). Electrical
requirements can be found on the back of the fixture.
WARNING: DO NOT use an extension cord. ONLY use power strips with integral
overcurrent protection.
The light's 5-ft. cord length restricts the maximum distance from an outlet the fixture can be mounted. Select a mounting location within 5 ft. of
an electrical outlet. VERIFY THE LOCATION WORKS PRIOR TO DRILLING. There are 2 basic ways to mount the light: chain mount or flush
mount. For CHAIN MOUNT WITH HOOK SCREWS, mark 2 mounting holes, 22-3/4 in. apart. For SURFACE MOUNT, mark 22-1/4 in. apart. ONLY
instructions for installing to a wood joist/stud or drywall are addressed here.
CHAIN MOUNT: Mount hardware 22-3/4 in. apart.
22-3/4 in.
Cx2
-or-
or
Dx2
1/16 in.
WOOD INSTALLATION: Using a 1/16-in. drill bit, drill the 2 pilot holes where either the hook screws or wood screws (C/D) will be installed. Insert the
hook screws or wood screws into the pilot holes. Tighten the screws until they are securely fastened into the mounting surface.
DRYWALL INSTALLATION: Use a 3/16-in. drill bit, drill out the 2 insertion holes for the wedge anchors (B). Pinch the wedge anchor tips
together (toward the center). Fully insert the folded wedge anchors into the holes until flush with the surface. Tighten the screws (C/D) into the wedge
anchors until they are securely fastened into the mounting surface.
Ex2
Ax2
Lampe de culture pour les plantes à DEL à spectre complet, réglable, de 61cm (Page 3)
Luz LED de crecimiento de plantas de espectro completo ajustable de 61cm (Página 6)
Power-In Port
Orifice d'alimentation
électrique
Puerto de entrada
de alimentación
Auto ON/OFF Light Timer Slide Switch
Interrupteur de marche/arrêt à glissière
pour minuterie d'éclairage automatique
Interruptor deslizante del temporizador de
luz de ENCENDIDO y APAGADO automático
* Actual hardware may differ from illustration./
* La quincaillerie incluse peut être différente de l'illustration./
* Los aditamentos reales pueden diferir de los que se muestran en la ilustración.
WARNINGS AND CAUTIONS
PRE-INSTALLATION
SURFACE MOUNT: Mount hardware 22-1/4 in. apart.
Cx2
It may be necessary to carefully tap
the end of the drywall anchor to get
it fully into place.
-or-
Dx2
Bx2
3/16 in.
CHAIN MOUNT INSTALLATION
IMPORTANT: The chains are
designed to hold the weight of the
fixture. Additional weight or force
applied to the fixture may cause the
chains to fail.
NOTE: Chain links can
always be removed to
reduce the length of the
chain.
SAVE AND ATTACH RECEIPT HERE.
2-ft. Adjustable Full Spectrum LED Plant Grow Light (Page 1)
Model / Model / Modelo #: GL1326-WHT-24LFC-G
Hardware / Petit matériel de
fixation*/ Aditamentos*
Ax2
12 in /
30,5 cm
WARNING: DO NOT look directly at LED light source for any extended period of time.
CAUTION: ONLY operate in areas with air temperatures ranging between -0°F to
104°F (-18°C to 40°C).
CAUTION: ONLY route and secure the cords in a manner where they will not be
pinched or damaged. DO NOT hang items from cords.
CAUTION: DO NOT mount to surfaces with a thickness less than 1/4 in. DO NOT
mount over sinks or stoves.
CAUTION: DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT. This fixture is
not dimmable.
Turn power off before servicing.
Indoor use only.
Suitable for damp locations.
22-1/4 in.
1
2
The screw must pierce through the top hole of the anchor.
Determine how high the fixture needs to be
suspended. Attach the "V" hook (E) to the bottom loop
of the chain (A) by fishing one end of the hook through
the bottom loop. Remove any kinks out of the chain.
Repeat on the other side.
Insert both ends of the "V" hook (E) through the small
rectangular slots along the top side of end caps and
pivot the ends through the opening.
Required/
Nécessaire/
Se necesita
Dx2
Ex2
1 2
or