Publicidad
Idiomas disponibles
Idiomas disponibles
Product Set Up
Open Stroller
1
- Take the stroller frame out. (1)
2
- Rotate the handle up to open the stroller frame. (2)
3
- Pull the seat to open it. (3)
A "click" sound means the seat is open.
Check that the stroller is completely latched open
before continuing.
Switch Seat
Please switch seat if you needed.
1
- Press the seat release button (4)-1 and lift the seat
up (4)-2.
2
- Reverse the seat, and then attach it to the frame.
(5)
A "click" sound means the seat is attached
completely.
Front Wheels
1
- Insert the front wheel into the front leg. (6)
A "click" sound means the front wheel is
assembled completely.
Check the wheel is securely attached by pulling
out.Repeat on opposite side.
2
- To remove the front wheel, press the release
button (7)-1 and detach the front wheel from the
front leg (7)-2.
Rear Wheels
1
- Insert the rear wheel into the rear leg. (8)
A "click" sound means the rear wheel is assembled
completely.
Check the wheel is securely attached by pulling
out.Repeat on opposite side.
2
- To remove the rear wheel, press the release button
(9)-1 and detach the rear wheel from the rear leg
(9)-2.
Arm Bar
Always secure the child with the harness. The arm
bar is not a restraint device.
1
- Align the arm bar ends with the arm bar mounts,
and insert until it clicks into place. (10)
A "click" sound means the arm bar is assembled
completely.
2
- To remove the arm bar, press the arm bar release
buttons (11)-1 and remove the arm bar (11)-2.
7
TRIV next instructions
Check Set Up
Stroller frame is latched open
Stroller seat securely attached
Rear and front wheels securely attached
Arm bar securely attached
Product Use
Securing Your Child
1
- Push the top button on the buckle (12)-1 to release
the buckle latch and remove the magnetic clips
(12)-2. Place your child in the stroller.
2
- Insert the magnetic clips into the buckle. (13)
3
- Fit the harness snugly to your child by pulling the
adjustment straps to tighten (14)-1. Then pull the
waist adjustment straps out (14)-2.
Shoulder Harness Position
1
- The upper shoulder harness buckles can be moved
up and down for added adjustment. (15)
To avoid serious injury from falling or sliding out,
always secure your child with the harness.
Make sure the harness is adjusted properly and
your child is snugly secured. The space between
the child and the shoulder harness should be about
the thickness of one finger.
DO NOT cross the shoulder belts. This will cause
pressure on child's neck.
Canopy
1
-
To open the canopy, pull the canopy toward the
front of the seat, and to fold, push it back. (16)
2
- Open the zipper on the canopy for extra shade. (17)
3
- For added ventilation, flip the canopy window
cover up. (18)
Recline
There are 4 recline positions for the backrest.
1
- To raise or lower the backrest, squeeze the recline
adjustment button (19)-1, and pull the backrest up
or down (19)-2.
Please do not press the button (19)-3 on the
middle of the recline adjustment button when
adjusting the angle for the recline.
Make sure the recline is adjusted properly for use.
Calf Support
The calf support has 2 use positions.
1
- To raise the calf support, lift up.
2
- To lower the calf support, press the adjustment
button (20)-1, and push down (20)-2.
Handle
The handle has 5 positions.
1
- To adjust the height of the handle, pull the handle
adjustment button (21)-1 and pull the handle up or
down (21)-2.
Brake
1
- To lock the rear wheels, step down on the brake
lever. (22)
2
- To unlock the rear wheels, step down the brake
lever again. (23)
Always apply the brake when the stroller is
stopped. Push the stroller slightly to ensure the
brake is engaged.
Front Swivel Locks
It is recommended to use the front swivel locks on
uneven surfaces.
1
- Pull the front swivel lock up to lock the front
wheel. (24)
2
- Push the front swivel lock down to unlock. (25)
Fold
The stroller can be folded with forward facing seat or
rear facing seat or without the seat. Before folding the
stroller, adjust the handle to the lowest position and
suggest the front swivel locks are locked.
1
- Fold the canopy. (26)
2
- Press the folding release button (27)-1 on the
middle of the recline adjustment button and then
squeeze the recline adjustment button (27)-2.
3
- Fold the seat. (28)
4
- Pull the folding webbing of the seat to fold the
stroller. (29)
5
- The stroller can stand by forward wheels swivel
locked. (30)
6
- Press the folding buttons of the seat mounts. (31)
7
- Fold the stroller. (32)
The stroller without seat can stand by handle and
the front wheels.
Insert
1
- To assemble the insert, place the insert over the
seat and thread the shoulder, waist and crotch
harnesses through their respective slots. (33)
Accessories
Not all accessories are included on some models.
Post adaptors
For Nuna infant carrier and TRIV carry cot assembly
and usage, please refer to the infant carrier and carry
cot instruction manual.
1
- To attach the post adaptors, place the post
adaptors on the seat mounts. A "click" sound
means the post adaptors are attached. (34)(35)
2
- To attach infant carrier, place the infant carrier
on the post adaptors. A "click" sound means the
infant carrier is attached. (36)
3
- To attach carry cot, place the carry cot on the post
adaptors. A "click" sound means the carry cot is
attached. (37)
4
- The infant carrier and carry cot angle can be
adjusted with our adjustable adaptors. (38)
5
- When used with rear facing, the letters on the
post adaptors are the same as those on the frame
plastic. (39)
6
- When used with front facing, the letters on the
post adaptors are opposite to those on the frame
plastic. (40)
7
- To remove the infant carrier, push the release
buttons on the infant carrier (41)-1 and lift up
(41)-2.
8
- To remove carry cot, press the release buttons on
the side of the carry cot (42)-1 and lift up (42)-2.
9
- To remove the post adaptors, pull the adaptor
release buttons (43)-1 and lift up (43)-2.
Remove the infant carrier and carry cot before
folding.
Fold the Stroller with Post adaptors
Before folding the stroller with post adaptors, adjust
the handle to the lowest position and suggest the front
swivel locks are locked.
1
- Pull the folding webbing of the post adaptors to
fold the stroller. (44)
The stroller with the post adaptors can stand by
handle and the front wheels.
TRIV Rain Cover
Check that the canopy is completely open before
attaching the rain cover.
1
- To assemble the rain cover, place it over the
pushchair. (45)
ALWAYS check ventilation when the rain cover is
on the product.
ALWAYS check that the rain cover has been
cleaned and dried before folding.
DO NOT fold the pushchair when the rain cover is
attached.
DO NOT place your child in the pushchair in hot
weather with the rain cover attached.
TRIV next instructions
8
Publicidad
