Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
XSVI-9006-NAV
VW CAN Interface 2015-up
• Provides accessory power (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, and speed sense)
• For use in non-amplified systems, or when replacing an amplified system
• 48 inch leads for remote tuner location
• Prewired ASWC-1 harness included (ASWC-1 sold separately)
• High level speaker input
• Retains balance and fade
• Micro "B" USB updatable
VOLKSWAGEN
Golf
axxessinterfaces.com
Axxess Integrate
Installation instructions for XSVI-9006-NAV
FEATURES
APPLICATIONS
2015-up
INTERFACE COMPONENTS
• XSVI-9006-NAV interface
• XSVI-9006-NAV harness
TOOLS REQUIRED
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)
CAUTION!
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con -
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
•
metraonline.com
Metra recommends disconnecting the negative bat -
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
Publicidad
Manuales relacionados para Axxess XSVI-9006-NAV
Resumen de contenidos para Axxess XSVI-9006-NAV
- Página 1 Installation instructions for XSVI-9006-NAV XSVI-9006-NAV INTERFACE COMPONENTS VW CAN Interface 2015-up • XSVI-9006-NAV interface • XSVI-9006-NAV harness FEATURES • Provides accessory power (12-volt 10-amp) TOOLS REQUIRED • Retains R.A.P. (retained accessory power) • Wire cutter • Crimp tool • Solder gun • Tape •...
-
Página 2: Important Warning
The following (3) wires are for aftermarket multimedia/navigation radios that provide From the XSVI-9006-NAV harness to the aftermarket radio: these wires (if not required, tape them off and disregard them). • Connect the Black wire to the ground wire. - Página 3 The DIN plug is to be connected to the optional AX-LCD screen (sold separately) to retain the personalization menu that is lost when removing the factory radio. Attention: If the XSVI-9006-NAV loses power for any reason, the following step will need to be performed again.
-
Página 4: Important
Installation instructions for XSVI-9006-NAV IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. -
Página 5: Vw Interfase Can 2015 Y Mas
Instrucciones de instalación para XSVI-9006-NAV XSVI-9006-NAV COMPONENTES DE LA INTERFASE VW interfase CAN 2015 y mas • Interfase XSVI-9006-NAV • Arnés XSVI-9006-NAV CARACTERÍSTICAS • Provee corriente de accesorios (12 voltios 10 amperes) HERRAMIENTAS REQUERIDAS • Retiene R.A.P. (corriente de accesorio retenida) •... -
Página 6: Advertencia Importante
• Conecte el cable púrpura con la salida positiva de la bocina derecha trasera. • Conecte el cable púrpura/negro con la salida negativa de la bocina derecha trasera. Desde el arnés XSVI-9006-NAV al radio de mercado secundario: Los siguientes (3) cables son para radios de mercado secundario con multimedios/ navegación que incluyen estos cables (si no se requieren, encíntelos e ignórelos). -
Página 7: Instalación Del Xsvi-9006-Nav
Atención: Si el XSVI-9006-NAV pierde la alimentación por cualquier motivo, deberá realizar el siguiente paso de nuevo. • Para inicializar la interfase, encienda la marcha y espere 30 segundos, luego... -
Página 8: Importante
Instrucciones de instalación para XSVI-9006-NAV IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones.