Axxess ASWC-1 Manual De Instalación
  1. Manuales
  2. Marcas
  3. Axxess Manuales
  4. Interfaces USB
  5. ASWC-1
  6. Manual de instalación
Axxess ASWC-1 Manual De Instalación

Axxess ASWC-1 Manual De Instalación

Ocultar thumbs Ver también para ASWC-1:
Tabla de contenido

Publicidad

Enlaces rápidos

Descargar este manual
INSTALLATION INSTRUCTIONS ASWC-1
ASWC-1
Axxess Steering Wheel Control
Interface Installation Manual
US. PAT. NOS. 8014920 and 8214105
Kit Features
• One Interface does it all - No additional interfaces needed
• Designed to be compatible with all major radio brands
• Auto detects vehicle type, radio connection, and presets controls
• Ability to dual assign steering wheel control buttons
• Can be manually programmed for most vehicles
• Memory retains settings even after battery disconnection
or interface removal
• Connection placements are all organized behind the radio
• Micro "B" USB updatable
interFace components
• ASWC-1 Interface • 12-pin harness with male 3.5mm
connector • Female 3.5mm connector with Brown and
Brown/White wires • 12k-ohm resistor
tools required
• Cutting tool • Crimping tool • Tape
METRA. THE WORLD'S BEST KITS.™
1-800-221-0932
metraonline.com
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION

Publicidad

Tabla de contenido
loading

Manuales relacionados para Axxess ASWC-1

Resumen de contenidos para Axxess ASWC-1

  • Página 1 INSTALLATION INSTRUCTIONS ASWC-1 ASWC-1 Axxess Steering Wheel Control Interface Installation Manual US. PAT. NOS. 8014920 and 8214105 Kit Features • One Interface does it all - No additional interfaces needed • Designed to be compatible with all major radio brands • Auto detects vehicle type, radio connection, and presets controls • Ability to dual assign steering wheel control buttons • Can be manually programmed for most vehicles • Memory retains settings even after battery disconnection or interface removal • Connection placements are all organized behind the radio • Micro “B” USB updatable interFace components • ASWC-1 Interface • 12-pin harness with male 3.5mm connector • Female 3.5mm connector with Brown and Brown/White wires • 12k-ohm resistor tools required • Cutting tool • Crimping tool • Tape METRA. THE WORLD’S BEST KITS.™...

  • Página 2: Tabla De Contenido

    Table of Contents Preface ....................3 Overview – Introduction to the ASWC-1 Interface and Wiring Harness ....4-5 ASWC-1 – Section 1: Installation ..............6-7 – Section 2: Programming ..............8-9 – Section 3: Troublshooting Auto Detect Mode ..............10 Manual Programming ............10-13 Changing Radio Type ............13-14 Manual Radio Type Programming .........14-15 – Section 4: Remapping Remapping SWC Buttons ............16 Resetting Original SWC Settings ..........17 ASWC-1 Legend – Vehicle LED Feedback ..............18 – Radio LED Feedback ..............18-19...

  • Página 3: Preface

    Preface What you need to know before you begin 1) Know the correct year, make, and model of your vehicle. 2) Be sure that the radio you are installing is compatible with the Axxess steering wheel control (ASWC-1) interface (refer to the aftermarket radio owner’s manual). 3) Go to the Axxess website (axxessinterfaces.com) and click on the link entitled “ASWC-1 VEHICLE INSTRUCTIONS”, which is located on the right side of the screen in the middle. Once you put your vehicle information in, click the “SUBMIT” button. This will take you to another page, where you will then click on the link under the word “DOCUMENTS”. This will provide the vehicle specific instructions for your vehicle. Print this document so you have it with you in the vehicle during the install as it is the best, and most recent source of information. Note: Even though we have done extensive research and testing (to verify that the steering wheel control wires we list are correct) it is still your responsibility to verify the steering wheel control wires with a multimeter.

  • Página 4: Overview

    Overview Introduction to the ASWC-1 Interface and Wiring Harness On the top of the ASWC-1 interface there are three points of interest: 1) The Programming LED – Flashes rapidly when in auto detect mode, f lashes slowly in manual programming mode. 2) The Reset Button – Hold down button for 3 seconds to start auto detect mode; hold down longer then 10 seconds to start manual programming mode. 3) The Slide Cover (USB Port Cover) – Open this up to reveal the USB update port. Using a standard Micro “B” to USB cable or Metra’s USB-MINI-CAB update cable you can make sure you always have the latest updated inventory. USB Port Cover Reset Button Programming LED...
  • Página 5 Overview Below are the wire colors for the ASWC-1. Please visit the Axxess website at www.axxessinterface.com for detailed information on your specific vehicle and for what color wire(s) to use with the ASWC-1 interface. Pin-1 Pink Pin-8 Black/Green Pin-2 White/Green Pin-9 Red (tip of 3.5mm connector) Pin-3 Yellow/Green Pin-10 White (ring of 3.5mm Pin-4 Green/Orange connector) Pin-5 Gray/Red Pin-11 Gray/Blue Pin-6 Black Pin-7 Blue/Pink Pin-12 Red...

  • Página 6: Section 1: Installation

    Section 1: Installation Once you have collected or printed out the information sheet on your particular vehicle from the Axxess website (www.axxessinterface.com) you’re ready to install the ASWC-1. Installing the ASWC-1 1) Connect the Black wire of the ASWC-1 to ground. You may use the same grounding point as the aftermarket radio. 2) Connect the Red wire of the ASWC-1 to a 12-volt accessory wire, one that turns “On” and “Off” with the ignition key. 3) Locate the correct SWC wire(s) in the vehicle’s radio primary or secondary harness as described in the vehicle information sheet found on the Axxess website. Connect the correct wire color(s) from the ASWC-1 to the steering wheel control wire(s) in the vehicle. Note: Metra recommends that the wire(s) are soldered for the best and most secure connection. T-Taps or scotch locks are not recommended due to the higher chance of an intermitted connection or change in resistive values.
  • Página 7 Section 1: Installation 4) If you are using an Eclipse, Kenwood, Metra OE, or a newer JVC radio, plug the included female 3.5mm connector with the Brown and Brown/White wires into the male 3.5mm connector of the ASWC-1 harness. • For Kenwood and select JVC: Connect the SWC wire (normally Blue/Yellow) to the Brown wire of the ASWC-1. Isolate and tape the Brown/White wire, it will not be used. Note: Some newer Kenwood radios will auto detect as a JVC. If this is the case, you can use a 12k-ohm resistor (included) in line between the Blue/Yellow and Brown wire of the female 3.5mm...

  • Página 8: Section 2: Programming

    Section 2: Programming The ASWC-1 can be programmed in two ways. (1) It can do it by itself through Auto Detect Mode, or (2) it can be manually programmed in non-data vehicles. It is strongly recommend to start with the Auto Detect Mode first. Auto Detect Mode: Overview The ASWC-1 has the ability to auto detect certain vehicles and to know what aftermarket radio it is connected to. The vehicle info sheet from the Axxess website (www.axxessinterface.com) will indicate if your vehicle will likely be auto detected and what action, if any, is required by you for this process to take place. For the Auto Detect feature to work there are 3 possible actions, however only one action will be required by you depending on your vehicle: • Turn the ignition on and no other action is required. • Turn the ignition on, press and hold the “Volume Up” button on the steering wheel. --- Or --- • Turn the ignition on, press and release the “Volume Up” button repeatedly on the steering wheel. As stated before, only one of these actions will need to be done depending on your vehicle for the Auto Detect feature to work. Please refer to the vehicle info sheet provided on the Axxess website. Auto Detect Mode: Steps 1) Complete connections to the vehicle and the aftermarket radio. If this is the first time the ASWC-1 is being installed in a vehicle:...
  • Página 9 2) Turn the ignition on, the LED will flash once, then go out. 3) Hold down the reset button for 3 seconds and then release it. 4) Perform action required for your particular vehicle as noted in the vehicle info sheet. 5) After a couple of seconds the LED should stop flashing and not light up for 2 seconds. At this point do not push any buttons. 6) After the 2 seconds there will be a series of 7 Green flashes, some short and some long. 7) The LED will pause for another 2 seconds then flash Red up to 11 times (refer to ASWC-1 ledgend). 8) This is the end of the auto detection stage. If the ASWC-1 detected the vehicle and the radio successfully the LED will light up solid. 9) For vehicles with OE Bluetooth buttons please press “Hang up” or “Pick up” on your steering wheel control after the LED on the ASWC-1 goes solid. If the OE Bluetooth buttons are able to be used, the LED will go out after 3 seconds. Your OE Bluetooth buttons are now programmed to your aftermarket radios Bluetooth buttons (aftermarket radio must have Bluetooth capabilities). Tip: If the LED does not light up solid refer to the troubleshooting section.

  • Página 10: Section 3: Troublshooting

    Section 3: Troubleshooting Auto Detect Mode So you tried the auto detect feature and at the end the LED did not stay solid “red”. Instead it started flashing, meaning that the ASWC-1 did not detect the vehicle. Follow these steps to determine what may have happened: 1) Verify that you have 12-volt accessory and a good ground to the ASWC-1. Sometimes the factory ground is not sufficient, a chassis ground is highly recommended. If your vehicle has a SWC reference ground wire, chassis ground that as well, along with your aftermarket radio. 2) Validate using the vehicle information sheet (Axxess website) that the correct steering wheel control wire(s), in the vehicle, were connected to the correct wire(s) to the ASWC-1. 3) Confirm that the 3.5mm connector is connected to your radio securely and in the correct location. 4) If using the female 3.5mm connector in Eclipse, Kenwood, select JVC, or Metra OE radios verify that the radio’s SWC wire is connected to the correct wire to the ASWC-1. Manual Programming Auto Detect Mode If your vehicle is not listed for auto detection by the ASWC-1 on the Axxess website, www.axxessinterface.com, you can manually program a non-data vehicle by the following steps (have ASWC-1 legend available).
  • Página 11 Please refer to the radio owner’s manual or wireless remote for specific commands that the radio will recognize. 1) Complete connections to the vehicle and to the aftermarket radio, make sure the 3.5mm connector is connected. If this is the first time the ASWC-1 is being installed in a vehicle: 2) Turn the ignition on; the LED will start flashing rapidly. 3) After 10 seconds the ASWC-1 will go into the LED feedback mode. After the series of LED flashes the LED will stay in a slow constant flash state. Go to step 4. --- Or --- If the ASWC-1 has been in a vehicle before: 2) Press and hold the reset button down for more then 10 seconds. 3) After the 10 seconds the LED will begin a slow constant flash.
  • Página 12 (2) After the 18th button is programmed or skipped the LED will go back to the slow constant blink mode. Note: If at any time an error is made hold down the reset button on the ASWC-1 for 10 or more seconds. This will restart the manual programming. Go back to Step 4 and start again. 8) Press and hold the “Volume Down” button for 5 seconds till the LED starts to flash quickly.

  • Página 13: Changing Radio Type

    Section 3: Troubleshooting 11) Then the LED will flash, up to 11 times, depending on what radio the ASWC-1 thinks it’s connected to. 12) Make sure the number of flashes match what radio you have installed. Refer to the Changing Radio Type section, pages 13-14. 13) If the LED flashes match the radio then hold down the “Volume Down” button until the LED goes solid red. 14) Programming for the vehicle and the radio is now complete. Test out the steering wheel control functions to make sure it works correctly. Changing Radio Type If the LED flashes do not match the radio you have connected, you must manually program the ASWC-1 to tell it what radio it is connected to. 1) To manually program the aftermarket radio, press and hold the “Volume Down” button on the steering wheel control until the LED goes solid red, then release “Volume Down”. 2) At this point Eclipse is programmed. If you are using an Eclipse radio go to step 3. If you are using a different radio go to step 4. 3) Press and hold “Volume Down” for 5 seconds. The LED will flash once then go solid red indicating the programming has finished. Go enjoy your radio. 4) If you have a different radio then Eclipse, press the Volume Up button again till the LED goes solid red, then release “Volume Up”. You have now programmed Kenwood.

  • Página 14: Manual Radio Type Programming

    Section 3: Troubleshooting 5) Here is the chart to show how many presses of the “Volume Up” button is needed for which radio you are trying to program: Eclipse Alpine Kenwood Visteon Valor Clarion “Type 1” 10 Clarion “Type 2” Sony and Dual 11 Metra OE Pioneer and Jensen 6) Once the radio manufacturer has been selected hold “Volume Down” for at least 5 seconds. The LED will flash the number of times which radio was selected then the LED will remain on to indicate the ASWC-1 has finished programming. Manual Radio Type Programming If only changing the radio type is needed then follow this procedure below. 1) Within the first 25 seconds of turning the key on, press and hold the car’s “Volume Down” button. 2) After 15 seconds of holding “Volume Down”, the ASWC-1’s red LED will go on.
  • Página 15 5) When the desired radio type has been reached, Press the “Volume Down” button. 6) The LED will go on and will remain on (approximately 3 seconds). The ASWC-1 is internally computing and storing this new information. 7) The LED will go “Off” indicating it is completed. Note: If at any time the user fails to press any button for a period of 10 seconds or more, this programing mode will abort.

  • Página 16: Section 4: Remapping

    Section 4: Remapping Remapping the SWC (Steering Wheel Control) Buttons Once you have the ASWC-1 programmed you can then change the steering wheel control button assignment(s). Such as, programing the “Seek Up” button as a “Mute” function. Follow the steps below to remap the SWC buttons: 1) Ideally have the ASWC-1 visible, so you can see the LED flashes to confirm button recognition. 2) Turning “Off” the radio is recommended. 3) Within the first 20 seconds of turning the ignition on, press and hold down the “Volume Up” button for at least 20 seconds. 4) The LED will light up solid red. Release “Volume Up” and the LED will go out. “Volume Up” has now been programmed. 5) Follow the list in the Button Assignment section, page 19, to reference the order of what buttons need to be pressed and/or how to bypass a button. 6) After the last button is programmed on your steering wheel (you do not have to go through the whole list), hold down the “Volume Up” button for at least 10 seconds then the LED will go out. --- Or --- After the 18th button is programmed or skipped the LED will go out and the remapping is completed.

  • Página 17: Resetting Original Swc Settings

    Section 4: Remapping Resetting Orginal SWC Settings If for any reason after remapping the steering wheel controls you want to revert back to the original steering wheel control settings, follow these steps: 1) Within the first 20 seconds of turning the ignition on. Press and hold down the original “Volume Down” button (not the “Volume Down” button you just remapped) for at least 25 seconds. 2) The LED will turn on then release the “Volume Down” button and the LED will turn “Off”. 3) The original steering wheel control settings will be restored.

  • Página 18: Aswc-1 Legend

    ASWC-1 Legend For A and B: Short flashes represent the steering wheel control wire(s) that are not connected to the vehicle from the ASWC-1. Long flashes represent wire(s) that are connected to the vehicle. A. Vehicle LED Feedback (Indicated by Green LED) 1st LED flash is the White/Green wire on the ASWC-1 2nd LED flash is the Orange/Green wire on the ASWC-1 3rd LED flash is the Green/Orange wire on the ASWC-1 4th LED flash is the Gray/Red wire on the ASWC-1 5th LED flash is the Black/Green wire on the ASWC-1 6th LED flash is the Gray/Blue wire on the ASWC-1 7th LED flash is the Pink wire on the ASWC-1 B. Radio LED Feedback (Indicated by Red LED) 1st LED flash is for Eclipse 2nd LED flash is for Kenwood 3rd LED flash is for Clarion (“Type” 1) 4th LED flash is for Sony and Dual 5th LED flash is for JVC 6th LED flash is for Pioneer and Jensen 7th LED flash is for Alpine* 8th LED flash is for Visteon 9th LED flash is for Valor 10th LED flash is for Clarion (“Type” 2) 11th LED flash is for Metra OE...

  • Página 19: Button Assignment (Remapping/Manual Programing)

    ASWC-1 Legend *Note (section B): If the ASWC-1 flashes 7 times and you do not have an Alpine radio connected to it that means that the ASWC-1 did not see any radio connected. Verify the 3.5mm connector is connected to the SWC input on the radio.

  • Página 20: Dual Assignment Instructions

    Dual Assignment Instructions Note: Seek up and Seek down are already set to Preset up and Preset down for long press. 1) Turn on the ignition but do not start the vehicle. 2) Press and hold down the steering wheel button that you want to assign a long press function to, for about ten seconds until the LED rapidly flashes green. At this point release the button and the LED will go solid green. 3) Press and release the VOLUME UP button the number of times corresponding to the new button number you selected (see chart below). The green LED will blink rapidly when the VOLUME UP is pressed and back to solid green when released. (Caution, if more than ten seconds elapses between a VOLUME UP button press, this procedure will abort, and the LED will go off). Go to the next step when the VOLUME UP button has been pressed the desired number of times. 4) To store the long press button in memory, press the button that you assigned a long press button (the button held down in step 1). The LED will now go off indicating it has been stored.
  • Página 21 Dual Assignment Instructions Button Number New Button Action Not allowed Not allowed SEEK UP/NEXT SEEK DOWN/PREV MODE/SOURCE MUTE PRESET UP PRESET DOWN POWER 10 BAND 11 PLAY/ENTER 12 13 ON HOOK 14 OFF HOOK 15 FAN UP 16 FAN DOWN 17 TEMP UP 18 TEMP DOWN...
  • Página 22 Notes...
  • Página 23 Notes...
  • Página 24 INSTALLATION INSTRUCTIONS ASWC-1 IMPORTANT WARNING This product includes instructions for installation which must be carefully followed. The instructions are worded in such a manner to assume that the installer is capable of completing these type of electronic installations. If you are unclear as to what you are instructed to do or believe that you do not understand the instructions so as to properly and safely complete the installation you should consult a technician who does have this knowledge and understanding. Failure to follow these instructions carefully and to install the interface as described could cause harm to the vehicle or to safety systems on the vehicle.

Este manual también es adecuado para:

Aswc

Tabla de contenido