Publicidad
Idiomas disponibles
Idiomas disponibles
C - Pan support :
Put the pan support in place. Pay attention to insert the 3
notches of its base in the 3 flaps of the center of the firebox.
The rotation of the support is blocked. Your appliance is
ready to be used as a stove. (Fig. 7)
D - Heat diffuser :
Place the heat diffuser on the top of the arms of the pan
support aligning the notches of its 3 supports with each
arm of the support. (Fig. 8)
E - Cooking griddle :
Place the cooking griddle on its 3 supports on top of the
firebox, paying attention to put the surface that you wish on
the top. (Fig. 9A & 9B)
Your appliance is ready to operate in Plancha or Grill mode.
IMPORTANT :
The heat diffuser must be placed underneath the cooking
plate before use in Grill or Plancha setting.
Never place the cooking utensils (frying pan, pan...) over
the cooking plate or the heat diffuser.
Warning :
If you see abnormal yellow flames or partial absence
of flame at the burner ports, it can be due to accidental
spilling water on the burner. Let it dry, the flame will return
to normal.
LIGHTING UP
Piezo Ignition (Fig. 10):
1. Open the gas supply turning the valve on the regulator
or the cylinder towards "+". (Fig. 10A)
2. Turn the control knob counter-clockwise to ignition
position (
GB
spark is created at the burner, it is lit at its Max power.
You can turn the control knob in the opposite direction
to reduce the power (between
3. If the burner fails to light, turn the control knob
clockwise to the off position (O) until it stops. Wait 5
minutes before repeating the operation.
4. If the burner does not ignite after 4 or 5 attempts, you
may A. proceed to Match Ignition at below section, or
B. read troubleshooting instructions in section H.
Match Ignition (Fig. 11):
If the piezo ignition doesn't work:
IMPORTANT: Wait until the appliance is cool, and wear
protective gloves before conducting following operations.
1. Open the gas supply turning the valve on the regulator
or the cylinder towards "+". (Fig. 11A)
2. If need to be, remove the cooking griddle, then put a lit
match near the burner. (Fig. 11B)
3. Turn the control knob to low heat setting (towards "
"). (Fig. 11C)
4. Place the cooking plate back on.
5. Adjust the power following your preference (between
and
)
COOKING
A - Using the appliance as a grill
1. Make sure that reservoir is filled with water to the
"MAXI" level and the pan support & cooking plate are
installed as described in section E.
2. Pre-heat the cooking plate for around 10 minutes at
maximum power in order to reach the ideal temperature
for cooking. Place your ingredients on the plate and
adjust the temperature with the control knob according
to your tastes.
). (Fig. 10B) When you hear a click, a
and
).
3. After 1 hour of cooking, check the quantity of water in
the tank. Add water till the MAX level if need to be.
The cooking plate is covered with a high quality non-
sticking material which ensures healthy cuisine without
adding fat or oil.
Fatty substances are collected in the water reservoir, your
meal is perfectly healthy (no residual or carbonised fats),
your ingredients retain all their savor.
A bluish discolouration of the cooking plate is due to the
strong heat development. This is without any impact on the
quality of the used material.
B - Using the appliance as a stove
IMPORTANT: Cooking plate must be taken away when
using the appliance as a stove. Never place cooking
vessels on the cooking plate or on the diffuser.
Place the cooking vessel (frying pan, pan...) on the pan
support, centered over the burner. Ensure that the flame
does not exceed the underside of the cooking vessel.
Do not use a cooking vessel smaller than 12 cm or larger
than 26 cm in diameter.
SHUTTING DOWN
Close the valve on the regulator or gas cylinder. (Fig. 3A)
When the flames have gone out, turn the control knob on
appliance to off position (O). (Fig. 3B)
F - REMOVING OR CHANGING THE GAS
CYLINDER
Always work in a well-ventilated area, never in the
presence of a flame, spark of heat source.
1. Close the control knob on the appliance by turning it
towards "O". (Fig. 3B)
2. Close the valve on the regulator or gas cylinder. (Fig.
3A)
3. Disconnect the regulator from the gas cylinder.
4. Install the new gas cylinder.
5. Connect the regulator to the new gas cylinder (check
the condition of the regulator seal, before connecting it
to the gas cylinder).
6. Check for gas leaks as instructed in section D.
20
Publicidad
