Publicidad
Idiomas disponibles
Idiomas disponibles
English
Trigger Operation With a Secondary
Trigger (Fig. A)
WARNING: Never inadvertently pull or grasp the
secondary trigger when moving about, changing
work location, when holstering or hanging tool, or
when preparing work surface for fastening operation.
WARNING: The operator must not hold the
secondary trigger pulled except during fastening
operation as serious injury could result if the trigger
accidentally contacts someone or something, causing
the tool to cycle.
When the trigger
is pulled, the tool will actuate each time
3
the primary trigger
2
is pulled. This trigger operated tool is
operated by first pulling or grasping the secondary trigger
under the hand grip, followed by pulling the trigger under
the valve.
Fastener Jam Clearing
Always disconnect the tool from air supply before clearing a
jammed fastener.
To clear a jammed fastener:
1. Release the loading hatch and pull it back.
2. Remove jammed fastener.
Tool Operation Check
WARNING: remove all fasteners from tool before
performing tool operation check.
Trigger Operation with a Secondary
Trigger
WARNING: The trigger will only actuate the tool if the
secondary trigger has already been pulled.
The secondary trigger is located under the handle. The
secondary trigger prevents the primary trigger from
actuating the tool if the secondary trigger has not been
pulled first.
Place the nose of the tool against a work piece for all of the
following operation checks.
1. With hand on rear end of the handle, further back away
from the secondary trigger, and not squeezing the
secondary trigger, use finger to pull the primary trigger.
THE TOOL MUST NOT CYCLE.
2. With hand on handle, and squeezing the secondary
trigger, use finger to pull the primary trigger. THE TOOL
MUST CYCLE.
While the secondary trigger remains squeezed, the tool will
cycle each time the primary trigger is pulled!
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories. An accidental
actuation can cause injury.
6
Air Supply-Pressure and Volume
Air volume is as important as air pressure. The air volume
supplied to the tool may be inadequate because of
undersize fittings and hoses, or from the effects of dirt and
water in the system. Restricted air flow will prevent the tool
from receiving an adequate volume of air, even though the
pressure reading is high. The results will be slow operation,
misfeeds or reduced driving power. Before evaluating tool
problems for these symptoms, trace the air supply from the
tool to the supply source for restrictive connectors, swivel
fittings, low points containing water and anything else that
would prevent full volume flow of air to the tool.
Repairs
WARNING:To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a CRAFTSMAN
factory service center or a CRAFTSMAN authorized
service center. Always use identical replacement parts.
Accessories
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be
used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
Versatrack™ (Fig. G)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories. An accidental
actuation can cause injury.
WARNING: To reduce the risk of serious personal
injury, do not use a damaged Versatrack™ hang hook
or Versatrack™ Trackwall. A damaged Versatrack™
hang hook or Versatrack™ Trackwall will not support
the weight of the tool.
WARNING: To reduce the risk of serious personal
injury, ensure the fitting holding the hang hook
is secure.
WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend
objects from the hang hook. ONLY suspend tool on the
Versatrack™ Trackwall using the hang hook.
WARNING: Ensure that the tool weight does not
exceed the maximum rated weight for the selected
Versatrack™ hook.
WARNING: When hanging objects on a Versatrack™
Trackwall rail, adequately space the tools in order to
not exceed 75 lb (35 kg) per linear foot.
1ST_Figure
1
G
8
Publicidad
