Publicidad
Idiomas disponibles
Idiomas disponibles
TNA ACTIVE LINE ARRAY SYSTEM
CONTROL PANEL
1. INPUT: Accepts a balanced/unbalanced line level XLR terminated signal.
2. VOLUME: Controls the overall output level of the TNA-2120SA and the
level present at FULL RANGE OUTPUT -A and FULL RANGE
OUTPUT -B.
3. MUTE / PROTECT INDICATOR: This illuminates if a fault condition
occurs. In this instance, the amplifier will shut down to prevent further
damage. Normal operation will resume once the fault condition has been
rectified.
PLEASE NOTE: On power down, the MUTE/PROT indicator will
illuminate to indicate the system is muted. At this point it is safe to disconnect
any cables.
4. POWER INDICATOR: Illuminates when the unit is connection to the
main supply and switched on.
5. CLIP: The led illuminates if any of the in-circuit limiters are triggered.
Reduce the VOLUME control to rectify this.
6. LINK OUT: A balanced output linked
directly from the INPUT.
7.PRESET SELECT and STATUS
INDICATORS:
DSP PRESET CHART
1
2
3
A
B
1A: FULL RANGE OUTPUT -A, optimised for 2 x TNA-2051, 0° tilt.
1B: FULL RANGE OUTPUT -B, optimised for 2 x TNA-2051, 0° tilt.
2A: FULL RANGE OUTPUT -A, optimised for 2 x TNA-2051, 8° tilt.
2B: FULL RANGE OUTPUT -B, optimised for 2 x TNA-2051, 8° tilt.
3A: FULL RANGE OUTPUT -A, optimised for 2 x TNA-2051, 0° tilt.
3B: FULL RANGE OUTPUT -B, optimised for 2 x TNA-2051, 8° tilt.
4A: FULL RANGE OUTPUT -A, optimised for 3 x TNA-2051, 0° tilt.
4B: FULL RANGE OUTPUT -B, optimised for 3 x TNA-2051, 0 tilt.
5A: FULL RANGE OUTPUT -A, optimised for 3 x TNA-2051, 0° tilt.
5B: FULL RANGE OUTPUT -B, optimised for 3 x TNA-2051, 8° tilt.
6A/B: FULL RANGE OUTPUT A/B, full range outputs for use with loudspeakers of your choice.
8. GROUND LINK: Is used to reduce the potential problem of earth loops when connecting to other equipment via the LINK OUT.
The control isolates/connects signal ground to safety ground of the LINK OUT XLR.
9. SUB OUT: A balanced line level signal for connecting additional active cabinets or a feed to a in-house PA system.
THIS OUTPUT CANNOT DIRECTLY DRIVE A LOUDSPEAKER.
10. MODE: It is important to set the mode switch properly to get the best performance from the system. When the mode switch is set
to LINE OUT, the XLR out is a full range line level signal, when the mode switch is set to Sub Out, the XLR out has a low pass filter
applied for direct connection to another powered subwoofer.
PLEASE NOTE: When set to SUB OUT, the internal woofers also have a Hi-pass filter applied, effectively making a true three-way
system. If no external subwoofer is used, be sure to leave this switch set to LINE OUT mode.
© 2022 HH Electronics Ltd
INPUT
2
2
1
3
3
LINK OUT
2
1
2
3
3
4
5
6
The onboard DSP optimises the equalisation characteristics for both
FULL RANGE-A and FULL RANGE-B outputs. Cycle through the presets via the
PRESET button, in conjunction with the DSP PRESET chart.
Designed and Engineered in the UK by HH Electronics LTD.
6
+
-
OFF
ON
GROUND LINK
8
°
LIVE SOUND & INSTALLATION
1
2
INPUT
VOLUME
0
10
LINK OUT
DSP PRESET
1
4
2
5
3
6
PRESET
(SEE TABLE)
SUB OUT
MODE
LINE OUT
SUB OUT
(INTERNAL SUBWOOFER HAS HPF APPLIED)
9
10
EN
EN
3
MUTE/PROT
POWER
4
5
CLIP
7
6
Publicidad
