Publicidad
Idiomas disponibles
Idiomas disponibles
OUTSIDE BACK EXHAUST
B
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
PREPARING THE REAR WALL
B1.
FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for
outside exhaust.
NOT E:
REA D
IT IS VER
AND FOL
Y IMPO
IN THE
LOW THE
RTA NT
INST ALLA
TO
BEF ORE
TION INST
DIRE CTIO
REA R
PRO CEE
RUC TION
NS
WAL L
DING
WITH
This Rear
TEM PLAT
THIS
S
mount ing
Wall Templ
E.
3/8" TO EDGE
plate and
ate serves
12"
outlet.
to locate
to positio
1. Use
a level
the horizo
n the bottom
accura
to check
ntal exhau
st
2. Locate
tely.
that the
templa
and mark
te is positio
right side
at least
ned
of the center
one stud
on the
4"
screw mount
I t is import
line.
left or
ed firmly
ant to use
of the microw
in a stud
at least
one wood
locatio ns
ave. Mark
to suppo
3. Drill
for the
supplie
two additio
rt the weight
holes in
the marke
d toggle
nal, evenly
spaced
a stud,
drill a 3/16"
d locatio
bolts.
that do
hole for
ns. Where
toggle
not line
up with
wood screws
there is
bolts.
a stud,
drill 5/8"
. For holes
D O NOT
holes for
AT THIS
TIME.
INSTA LL
4. Remov
THE MOUN
5. Review
e the templa
TING PLATE
the Installa
te from
the rear
installa
tion situatio
tion Instruc
wall.
n.
tion book
for your
Darle vuelta
versió n
a la hoja
en Españ
para consu
ol.
ltar la
Loca te
and mark
mou nting
holes to
plate .
align with
IMPO RTA
holes in
NT:
the
LOC ATE
AT LEAS
THE CEN
T ONE
TER LINE
STU D
MAR K
.
ON EITH
THE LOC
ER SIDE
SPA CED
ATIO N
OF
TOG GLE
FOR 2
ADD ITIO
ARE A.
BOL TS
NAL , EVE
IN THE
MOU NTIN
NLY
G PLAT
E
Trim the
rear wall
temp late
alon g
the dotte
d line.
Loca te
and mark
mou nting
holes to
plate .
IMPO RTA
NT:
LOC ATE
AT LEAS
THE CEN
TER LINE
MAR K
THE LOC
SPA CED
ATIO N
ARE A.
TOG GLE
•
Read the instructions on the REAR
WALL TEMPLATE.
•
Tape it to the rear wall.
•
Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
Installation Instructions
NOTE: IT IS VERY IMPORTANT
TO
READ AND FOLLOW
THE DIRECTIONS
N INSTRUCTIO NS
IN THE INSTALLATIO
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
serves to position the bottom
This Rear Wall Template
the horizontal exhaust
mounting plate and to locate
outlet.
that the template is positioned
1. Use a level to check
2. Locate and mark at least
accurately.
one stud on the left or
right side of the centerline.
It is important to use at
least one wood
a stud to support the weight
screw mounted firmly in
of the microwave. Mark
two additional, evenly spaced
toggle bolts.
locations for the supplied
locations. Where there is
3. Drill holes in the marked
for wood screws. For holes
a stud, drill a 3/16" hole
a stud, drill 5/8" holes for
that do not line up with
toggle bolts.
MOUNTING PLATE
DO NOT INSTALL THE
AT THIS TIME.
from the rear wall.
4. Remove the template
5. Review the Installation
Instruction book for your
installation situation.
para consultar la
Darle vuelta a la hoja
versión en Español.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE .
EVENLY
MARK THE LOCATION
FOR 2 ADDITIONAL,
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
along the dotted line.
Trim the rear wall template
Trim the
rear wall
temp late
alon g
the dotte
d line.
align with
holes in
the
T ONE
STU D
.
ON EITH
ER SIDE
FOR 2
OF
ADD ITIO
BOL TS
NAL , EVE
IN THE
MOU NTIN
NLY
G PLAT
E
(Horizontal Duct)
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
4"
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE .
EVENLY
MARK THE LOCATION
FOR 2 ADDITIONAL,
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
REMOVE BLOWER PLATE
B2.
Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.
Blower Plate
EN-16
Back of
Microwave
Publicidad
