Descargar Imprimir esta página

Battery Notes; Battery Disposal - EAS ELECTRIC ECRL66A Manual De Instrucciones

Publicidad

Idiomas disponibles

Idiomas disponibles

Function Buttons
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote
control. The following is a brief introduction to the remote control itself. For instructions on how to
operate your air conditioner, refer to the How to Use The Basic/Advance Functions section of
this manual.
NOTE:Please do not select HEAT mode if the machine you purchased is cooling only
type. Heat mode is not supported by the cooling only appliance.
ON/OFF
Turns the unit on or off
MODE
Scrolls through operation
modes as follows:
AUTO  COOL  DRY 
HEAT  FAN
ECO
Starts and stops energy
efficient feature. If hold
down this button for
more than 2 seconds,
Mode
the sleep feature is
activated.
TIMER
Sets timer to turn unit on
Timer
Timer
and off(see How to Use
Basic Functions for
instructions)
LED
LED
,
Turbo
Turns indoor unit s LED
display on and off.
FOLLOW ME
Temperature sensing and
room temperature display
button.
TURBO
Enables unit to reach
preset temperature in
SHOUT CUT
shortest possible time
Sets and activates your
favourite pre-settings.
Model:ECRL66B
V.2
FAN
Selects fan speeds in
the following order:
AUTO  LOW 
MED  HIGH
NOTE: Holding this button
down for 2 seconds will
activate Silence feature.
TEMP
Increases temperate in
1 C increments.
O
Max. temperature is
ON/OFF
Fan
30 C .
O
TEMP
Decreases temperate in
1 C increments.
O
Swing
Min. temperature is
17 C .
O
Follow
Direct
me
SWING
Starts and stops horizontal
Self
Short
clean
cut
louver auto swing feature.
DIRECT
Used to set the desired
up/down air flow direction.
The louver changes 6
degree in angle for each
press.
SELF CLEAN
Starts and stops the unit
self clean feature.
3
HANDLING THE REMOTE CONTROLLER
NOT SURE WHAT A FUNCTION DOES?
Refer to the How to Use Basic Functions
and How to Use Advanced Functions
sections of this manual for a detailed
description of how to use your air conditioner.
SPECIAL NOTE
Button designs on your unit may differ
slightly from the example shown.
If the indoor unit does not have a particular
,
function, pressing that function s button on
the remote control will have no effect.
INSERTING AND REPLACING BATTERIES
Your air conditioning unit comes with two
AAA batteries. Put the batteries in the
remote control before use:
1. Remove the back cover from the remote
control, exposing the battery compartment.
2. Insert the batteries, paying attention to
match up the (+) and (-) ends of the
batteries with the symbols inside the
battery compartment.
3. Install the back cover on.
INSTALLING REMOTE CONTROL HOLDER
The remote controller can be attached to a wall
or stand by using a remote controller holder
(optional part, not supplied with the unit).
1.
Before installing the remote controller, check
that the air conditioner receives the signals
properly.
2. Install the holder with two screws.
3. Put
the remote controller in the holder.

BATTERY NOTES

For optimum product performance:
Do not mix old and new batteries, or
batteries of different types.
Do not leave batteries in the remote control
,
if you don t plan on using the device for
more than 2 months.

BATTERY DISPOSAL

Do not dispose of batteries as unsorted
municipal waste. Refer to local laws for
proper disposal of batteries.
TIPS FOR USING REMOTE CONTROL
The remote control must be used within 8
meters of the unit.
The unit will beep when remote signal is
received.
Curtains, other materials and direct
sunlight can interfere with the infrared
signal receiver.
Remove batteries if the remote control
will not be used more than 2 months.
Remove the back cover
to install batteries
Put the remote controller
in the holder.
4
V.2

Publicidad

loading

Este manual también es adecuado para:

Ecrl66b