Intimus 45 SP2 Instrucciones De Uso página 5

GB
IMPORTANT SAFETY NOTES
<< The machine may not be operated by
more than one person at any given
time!
The machine was designed for safe
operation by "one person only".
<< During the shredding process no other
work may be performed on the machi-
ne (for example cleaning, etc.)!
<< The machine is not a toy, and is not
suitable for use by children!
The overall technical safety concept of
this machine (dimensions, feed open-
ings, emergency shutdown devices
etc.) does not provide for any guarantee
regarding hazard-free operation by
children.
<< Danger of injury! Keep all
loose articles of clothing, ties,
jewelery, long hair or other
loose objects away from
opening!
CONTROLS:
1 = Main plug (fig. 2)
When the machine is first plugged in it is
not on.
2 = Function button (fig. 1)
"Ready"/ "Off" / "Stop"
This button has three functions:
a) "Ready"
The machine changes to "Ready" if you
press this button briefly.
At the same time the integral LED
display comes on.
b) "Off"
The machine switches off if it is in the
"Ready" mode and the button is held
down for about 3 seconds.
Note: The machine
automatically if it is not used for about 5
minutes.
c) "Stop"
If you press this button briefly when the
cutters are running they switch off and
stop.
6
7
8
2
Fig. 1
<< Danger of injury! Never insert fingers
<< In case of danger switch the machine
<< Always unplug the machine from the
Special materials
Symbol
Model
45/60SP2 (SC2)
45/60CP4 (CC3)
45/60CP5 (CC4)
45/60CP6 (CC5)
45/60CP7 (CC6)
3 = Forwards button (fig. 1)
This button has two functions:
a) If this button is pressed briefly, the
cutting mechanism runs forwards for a
few seconds, e.g. to remove remaining
material from the cutting mechanism.
At the same time the integrated LED
display
b) If this button is pressed and held
for approx. two secs., the cutting
mechanism runs forwards continually
and materials to be shredded can be fed
into the machine. At the same time the
integrated LED display
4 = Reverse button (fig. 1)
If you press this button the cutters run
switches off
backwards for a short time. At the same
time the integral LED display
5 = Light barrier (Forward motion) (fig. 3)
The shredding procedure starts as soon
as material is fed into the feed slot. At the
same time the integral forward button LED
display
3
9
10
1
4
45 SP2(SC2)/CP4(CC3)/CP5(CC4)/CP6(CC5)/CP7(CC6)
60 SP2(SC2)/CP4(CC3)/CP5(CC4)/CP6(CC5)/CP7(CC6)
into opening!
off with the mains switch, or with the
emergency switch, or unplug the ma-
chine!
mains power supply before opening
the machine!
Repairs may only be performed by
trained personnel!
X
X X X
X = not applicable for shredding
OPERATION
lights up.
lights up.
comes on.
comes on.
Fig. 2
5
INITIATION
AREA OF APPLICATION:
The intimus 45/60SP2(SC2)/CP4(CC3)/
CP5(CC4)/CP6(CC5)/CP7(CC6) data shredder
is a machine used for shredding general
documents.
Generally the machine may only be
used to shred paper (deviations see
table below "special materials")!
Shredding of other types of data carriers
may lead to injuries (for example due to
splintering of hard materials etc.) and
damage to the machine (for example
destruction of the cutter etc.).
INSTALLATION:
- Unpack the machine and put it together.
- Fit the plastic bag onto the bag frame.
- Connect the machine to the power with the
plug (1) (Fig. 2) (For information on the right
fuse for the plug see "TECHNICAL DATA").
X
The socket outlet shall be installed near the
X
equipment and shall be easily accessible!
X
Only operate the machine in enclosed
X
rooms at temperatures between 10°C
X
and 25°C!
6 = Control display (fig. 1)
"Material jam in machine" / "Light
barrier covered when door opens or
when machine turned on"
For the procedures see the relevant
description under the "MALFUNCTION"
section.
a) "Material jam in machine"
Comes on when too much material has
been fed into the cutters. The cutters
jam, then run in reverse for a short time
and stop. The motor switches off.
b) "Light barrier covered
when door open"
Comes on when there is still material in
the feed slot when the door is opened.
The cutters stop. The motor switches
off.
c) "Light barrier covered
when machine turned on"
Comes on when there is still material
in the feed slot when the machine is
switched on.
11
Fig. 3
5